Pos | standard Number | publication date | Language | Description |
1 | SAE AMS3895B-1994 | 1994-07-01 | English | Broadgoods and Tape, Carbon Fiber-Epoxy Resin Impregnated Multi-Ply, Uniform Fiber |
2 | SAE MAP1201-1994 | 1994-07-01 | English | Tolerances, Hexagon Bar, Machined Flat and Forged Wrenching Flat Sizes for Fluid Fittings, Metric |
3 | SAE AMS2604F-1994 | 1994-07-01 | English | Pressure Testing, Gaseous Media 40 psi DoD Adopted |
4 | SAE ARP578-1994 | 1994-07-01 | English | DETAIL REQUIREMENTS FOR 4000 AND 5000 PSI AIRCRAFT |
5 | SAE AS4203A-1994 | 1994-07-01 | English | FITTING, BEAM SEAL, FEMALE TUBE END INTERNAL SWAGE, 4000 PSI, HYDRAULIC |
6 | SAE J217-1994 | 1994-07-01 | English | (R) Stainless Steel 17-7 PH Spring Wire and Springs |
7 | SAE CMB 6-1C-1994 | 1994-07-01 | English | Configuration and Data Management References - Formerly TechAmerica CMB 6-1C |
8 | SAE AMS3728A-1994 | 1994-07-01 | English | Epoxy Cresol Novolac Resin Low Molecular Weight |
9 | SAE AS7106-1994 | 1994-07-01 | English | National Aerospace and Defense Contractors Accreditation Program Quality Program Requirements |
10 | SAE ARP4050-1994 | 1994-07-01 | English | Balancing Machines - Description and Evaluation Vertical, Two-Plane, Hard-Bearing Type for Gas Turbine Rotors ANSI Approved |
11 | SAE AS7107-1994 | 1994-07-01 | English | National Aerospace and Defense Contractors Accreditation Program Inspection System Requirements |
12 | SAE AMS3913B-1994 | 1994-06-01(R 2014) | English | Radome, Foam Sandwich Hot-Melt, Addition-Type Polyimide |
13 | SAE AMS3729A-1994 | 1994-06-01(R 2014) | English | Epoxy Resin Matrix, Thermosetting Moderate Temperature Resistant, Unfilled |
14 | SAE J1981-1994 | 1994-06-01(R 2011) | English | Road Hazard Impact Test for Wheel and Tire Assemblies (Passenger Car, Light Truck, and Multipurpose Vehicles) |
15 | SAE AIR1083B-1994 | 1994-06-01(R 2007) | English | Airborne Hydraulic and Control System Survivability for Military Aircraft |
16 | SAE AS4832-1994 | 1994-06-01(R 2006) | English | Gland Design: Nominal 3/8 in Cross Section for Custom Compression Type Seals |
17 | SAE AMS3913B-1994 | 1994-06-01(R 2005) | English | Radome, Foam Sandwich Hot-Melt, Addition-Type Polyimide |
18 | SAE AMS3729A-1994 | 1994-06-01(R 2005) | English | Epoxy Resin Matrix, Thermosetting Moderate Temperature Resistant, Unfilled |
19 | SAE AMS3573B-1994 | 1994-06-01(R 2003) | English | Resin, Polyurethane (EU) Casting Polyether-Type, Flexible, Solid Low-Temperature Resistant, 80 to 90 |
20 | SAE AMS3614B-1994 | 1994-06-01(R 2003) | English | Polycarbonate Sheet and Parts Optical Grade, Coated |
21 | SAE J57-1994 | 1994-06-01(R 2000) | English | Sound Level of Highway Truck Tires |
22 | SAE ARP4118-1994 | 1994-06-01 | English | Isolation and Corrosion Protection of Dissimilar Materials |
23 | SAE J1694-1994 | 1994-06-01 | English | Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - Performance Requirements, Recommended Practice |
24 | SAE AS4832-1994 | 1994-06-01 | English | Gland Design: Nominal 3/8 in Cross Section for Custom Compression Type Seals |
25 | SAE AMS3837D-1994 | 1994-06-01 | English | Cloth, Type "S" Glass 181 Style Fabric, Finish No. HTS-904 DoD Adopted |
26 | SAE AMS3847C-1994 | 1994-06-01 | English | Cloth, Quartz, "B" Stage Polyimide Resin Impregnated Style 581 Fabric, 315 Degrees C (599 Degrees F) DoD Adopted |
27 | SAE J1693-1994 | 1994-06-01 | English | Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - General Characteristics and Test Procedure, Recommended Practice |
28 | SAE J1744-1994 | 1994-06-01 | English | 280 Relay Footprint, Standard |
29 | SAE J271-1994 | 1994-06-01 | English | (R) Special Quality High- Tensile, Hard-Drawn Mechanical Spring Wire and Springs, Recommended Practice ANSI Approved |
30 | SAE J114-1994 | 1994-06-01 | English | (R) Seat Belt Hardware Webbing Abrasion Performance Requirements ANSI Approved |
31 | SAE J384-1994 | 1994-06-01 | English | (R) Motor Vehicle Seat Belt Anchorages - Test Procedure ANSI Approved |
32 | SAE J113-1994 | 1994-06-01 | English | (R) Hard-Drawn Mechanical Spring Wire and Springs, Recommended Practice ANSI Approved |
33 | SAE J132-1994 | 1994-06-01 | English | (R) Oil-Tempered Chromium-Vanadium Valve Spring Quality Wire and Springs, Recommended Practice |
34 | SAE J351-1994 | 1994-06-01 | English | (R) Oil-Tempered Carbon-Steel Valve Spring Quality Wire and Springs, Recommended Practice ANSI Approved |
35 | SAE J339-1994 | 1994-06-01 | English | (R) Seat Belt Hardware Webbing Abrasion Test Procedure ANSI Approved |
36 | SAE J230-1994 | 1994-06-01 | English | (R) Stainless Steel, SAE 30302, Spring Wire and Springs |
37 | SAE J316-1994 | 1994-06-01 | English | (R) Oil-Tempered Carbon- Steel Spring Wire and Springs, Recommended Practice ANSI Approved |
38 | SAE AMS4619E-1994 | 1994-06-01 | English | MANGANESE BRONZE FORGINGS |
39 | SAE J2071-1994 | 1994-06-01 | English | Aerodynamic Testing of Road Vehicles - Open Throat Wind Tunnel Adjustment, Information Report |
40 | SAE AS1252A-1994 | 1994-05-01(R 2014) | English | TEE, FLARED TUBE FOR SEAL RING |
41 | SAE AS1253B-1994 | 1994-05-01(R 2014) | English | TEE, FLARED TUBE, BULKHEAD UNIVERSAL ON SIDE, FOR SEAL RING |
42 | SAE AS1250A-1994 | 1994-05-01(R 2014) | English | ELBOW, 90°, FLARED TUBE FOR SEAL RING |
43 | SAE AS1097B-1994 | 1994-05-01(R 2014) | English | SEAL RING, 37° FLARED TUBE FITTING END |
44 | SAE AS1249A-1994 | 1994-05-01(R 2014) | English | ELBOW, 45°, FLARED TUBE BULKHEAD UNIVERSAL, FOR SEAL RING |
45 | SAE AS1367A-1994 | 1994-05-01(R 2014) | English | Cross, Flared Tube for Seal Ring |
46 | SAE AS1365A-1994 | 1994-05-01(R 2014) | English | Tee, Flared Tube, Bulkhead Universal on Run, for Seal Ring |
47 | SAE AS1366A-1994 | 1994-05-01(R 2014) | English | ELBOW, 90°, FLARED TUBE BULKHEAD UNIVERSAL, FOR SEAL RING |
48 | SAE ARP4024-1994 | 1994-05-01(R 2013) | English | Aircraft/Engine Fuel Pump Net Positive Suction Pressure Performance Test and Evaluation |
49 | SAE AIR4830-1994 | 1994-05-01(R 2009) | English | Aircraft Tire Condition Monitoring Systems |
50 | SAE AS1097B-1994 | 1994-05-01(R 2007) | English | SEAL RING, 37掳 FLARED TUBE FITTING END |
51 | SAE AS1366A-1994 | 1994-05-01(R 2007) | English | ELBOW, 90掳, FLARED TUBE BULKHEAD UNIVERSAL, FOR SEAL RING |
52 | SAE AS1367A-1994 | 1994-05-01(R 2007) | English | Cross, Flared Tube for Seal Ring |
53 | SAE AS1365A-1994 | 1994-05-01(R 2007) | English | Tee, Flared Tube, Bulkhead Universal on Run, for Seal Ring |
54 | SAE ARP4024-1994 | 1994-05-01(R 2007) | English | Aircraft/Engine Fuel Pump Net Positive Suction Pressure Performance Test and Evaluation |
55 | SAE AS1253B-1994 | 1994-05-01(R 2007) | English | TEE, FLARED TUBE, BULKHEAD UNIVERSAL ON SIDE, FOR SEAL RING |
56 | SAE AS1252A-1994 | 1994-05-01(R 2007) | English | TEE, FLARED TUBE FOR SEAL RING |
57 | SAE AS1250A-1994 | 1994-05-01(R 2007) | English | ELBOW, 90掳, FLARED TUBE FOR SEAL RING |
58 | SAE AMS1383A-1994 | 1994-05-01(R 2007) | English | Oxide Conditioner, Alkaline Permanganate Aircraft Turbine Engine Components DoD Adopted |
59 | SAE MA4570-1994 | 1994-05-01(R 2007) | English | HO SE ASSEMBLY, PTFE, ARAMID REINFORCED, STANDARD DUTY, 21 000/28 000 kPa, 135 掳C, TITANIUM FITTINGS, FLARELESS, INCLUDING JUMP SIZES, STRAIGHT TO 90掳, METRIC |
60 | SAE AS1249A-1994 | 1994-05-01(R 2007) | English | ELBOW, 45掳, FLARED TUBE BULKHEAD UNIVERSAL, FOR SEAL RING |
61 | SAE MA4626-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, Straight to 90 Degrees, Metric |
62 | SAE MA4627-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, 45 Degrees to 45 Degrees, Metric |
63 | SAE MA4568-1994 | 1994-05-01(R 2004) | English | HOSE ASSEMBLY, PTFE, ARAMID REINFORCED STANDARD DUTY, 21 000/28 000 kPa, 135 DEGREES C, TITANIUM FITTINGS, FLARELESS, INCLUDING JUMP SIZES, STRAIGHT TO STRAIGHT, METRIC |
64 | SAE MA4571-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Aramid Reinforced, Standard Duty, 21 000/28 000 kPa, 135 Degrees C, Titanium Fittings, Flareless, 45 Degrees to 90 Degrees, Metric |
65 | SAE MA4623-1994 | 1994-05-01(R 2004) | English | Hose Assembly, Polytetrafluoroethylene, Para Aramid Reinforced Heavy-Duty, 21 000 kPa, 135 Degrees C, Aircraft Hydraulic Systems, Metric |
66 | SAE MA4573-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Aramid Reinforced, Standard Duty, 21 000/28 000 kPa, 135 Degrees C, Titanium Fittings, Flareless, 90 Degrees to 90 Degrees, Metric |
67 | SAE MA4572-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Aramid Reinforced, Standard Duty, 21 000/28 000 kPa, 135 Degrees C, Titanium Fittings, Flareless, 45 Degrees to 45 Degrees, Metric |
68 | SAE MA4629-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, 90 Degrees to 90 Degres, Metric |
69 | SAE MA4569-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Aramid Reinforced, Standard Duty, 21 000/28 000 kPa, 135 Degrees C, Titanium Fittings, Flareless, Including Jump Sizes, Straight to 45 Degrees, Metric |
70 | SAE MA1975-1994 | 1994-05-01(R 2004) | English | Hose Assemblies, Polytetrafluoroethylene, Aramid Reinforced, 135 Degrees C, Standard Duty, 28 000/21 000 kPa, Hydraulic, Aircraft Systems |
71 | SAE MA4625-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, Straight to 45 Degrees, Metric |
72 | SAE MA4624-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, Straight to Straight, Metric |
73 | SAE MA4628-1994 | 1994-05-01(R 2004) | English | Hose Assembly, PTFE, Para Aramid Reinforced, Heavy-Duty, 21 000 kPa, 135 Degrees C, Flareless, Titanium Fittings, Jump Sizes, 45 Degrees to 90 Degrees, Metric |
74 | SAE AS4283A-1994 | 1994-05-01(R 2004) | English | Handles and Attachments for Hand Socket Wrenches DoD Adopted |
75 | SAE J2204-1994 | 1994-05-01 | English | Tire Size Differential - Articulated Wheel Loader, Standard |
76 | SAE AIR4725-1994 | 1994-05-01 | English | Long-Term Storage Reliability of High Pressure Gas Containers for Pneumatic Actuation Systems ANSI Approved |
77 | SAE MA1975-1994 | 1994-05-01 | English | Hose Assemblies, Polytetrafluoroethylene, Aramid Reinforced, 135 °C, Standard Duty, 28 000/21 000 kPa, Hydraulic, Aircraft Systems |
78 | SAE MA4625-1994 | 1994-05-01 | English | HOSE ASSEMBLY, PTFE, PARA ARAMID REINFORCED, HEAVY-DUTY, 21 000 KPA, 135 ⁰C, FLARELESS, TITANIUM FITTINGS, JUMP SIZES, STRAIGHT TO 45⁰, METRIC |
79 | SAE MA4570-1994 | 1994-05-01 | English | HOSE ASSEMBLY, PTFE, ARAMID REINFORCED, STANDARD DUTY, 21 000/28 000 kPa, 135 °C, TITANIUM FITTINGS, FLARELESS, INCLUDING JUMP SIZES, STRAIGHT TO 90°, METRIC |
80 | SAE AMS4247B-1994 | 1994-05-01 | English | Aluminum Alloy, Hand Forgings 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049- T7352) Solution Heat Treated, Stress Relieved by Compression, and Precipitation Heat Treated - UNS A97049 DoD Adopted |
81 | SAE ARP4024-1994 | 1994-05-01 | English | Aircraft/Engine Fuel Pump Net Positive Suction Pressure Performance Test and Evaluation |
82 | SAE AMS3832C-1994 | 1994-05-01 | English | Roving, Type "S-2" Glass Epoxy Resin Impregnated DoD Adopted |
83 | SAE J1462-1994 | 1994-05-01 | English | (R) External Automatic Slack Adjuster Test Procedure, Recommended Practice |
84 | SAE AS1376D-1994 | 1994-04-01(R 2013) | English | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD |
85 | SAE AS1501C-1994 | 1994-04-01(R 2013) | English | Hose, Air Duct, Flexible, Nonmetallic, Aircraft |
86 | SAE AMS1548A-1994 | 1994-04-01(R 2008) | English | Cleaner, Turbine Engine Gas Path Solvent Emulsion Type |
87 | SAE AMS1500C-1994 | 1994-04-01(R 2008) | English | SOAP, LIQUID HAND Coconut-Oil Base |
88 | SAE AS1376D-1994 | 1994-04-01(R 2004) | English | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD DoD Adopted |
89 | SAE AIR1168/6-1994 | 1994-04-01(R 2004) | English | Characteristics of Equipment Components, Equipment Cooling System Design, and Temperature Control System Design |
90 | SAE AMS3617D-1994 | 1994-04-01(R 2003) | English | Nylon Plastic, Moldings and Extrusions |
91 | SAE J2245-1994 | 1994-04-01(R 2002) | English | Recommended Practice for Splash and Spray Evaluation |
92 | SAE MA2140-1994 | 1994-04-01 | English | HOSE ASSEMBLIES, POLYTETRAFLUOROETHYLENE, ARAMID REINFORCED, 28 000 KAP, HYDRAULIC AND PNEUMATIC |
93 | SAE AMS3823D-1994 | 1994-04-01 | English | Cloth, Glass Style 7781, Chrome-Silane Finish DoD Adopted |
94 | SAE J1679-1994 | 1994-04-01 | English | Peel Strength of Soft Trim Adhesives, Recommended Practice |
95 | SAE AMS7284A-1994 | 1994-04-01 | English | Rings, Sealing, Phosphonitrilic Fluoroelastomer (FZ) Aviation Fuel-Resistant - Reaffirmed Noncurrent April 2001 |
96 | SAE J1700-1994 | 1994-04-01 | English | Softening Point of Interior Trim Adhesives, Recommended Practice |
97 | SAE AS7200/1A-1994 | 1994-04-01 | English | National Aerospace and Defence Contractors Accreditation Program (NADCAP) Audit and Inspection Procedures and Checklists for the Sealant Manufacturers Accreditation Program |
98 | SAE AMS1546A-1994 | 1994-04-01 | English | Compound, Carbon Removing, Orthodichlorobenzene for Engine Parts DoD Adopted |
99 | SAE AMS3720B-1994 | 1994-04-01 | English | Paper Honeycomb 60 lb (25 kg) Paper DoD Adopted |
100 | SAE ARP4776-1994 | 1994-03-01(R 2012) | English | Pallet/Container Loader Auto-Levelling Systems |
101 | SAE AMS2399A-1994 | 1994-03-01(R 2011) | English | Electroless Nickel-Boron Plating |
102 | SAE AMS2550E-1994 | 1994-03-01(R 2009) | English | TREATMENT OF SHEET METAL PARTS Corrosion-Resistant Steel DoD Adopted |
103 | SAE ARP4776-1994 | 1994-03-01(R 2008) | English | Pallet/Container Loader Auto-Levelling Systems |
104 | SAE J1702-1994 | 1994-03-01(R 2007) | English | Self-Propelled Sweepers Sweep-Ability Performance |
105 | SAE J1093-1994 | 1994-03-01(R 2007) | English | (R) Latticed Crane Boom Systems - Analytical Procedure, Information Report |
106 | SAE AIR4783-1994 | 1994-03-01(R 2007) | English | Glossary of Terms - Aircraft Ground Refueling |
107 | SAE MA2151-1994 | 1994-03-01(R 2004) | English | Clamp Assemblies, Saddle or Omega Style, Two Point Mount, Multiple Shapes, Metric DoD Adopted |
108 | SAE ARP4776-1994 | 1994-03-01 | English | Pallet/Container Loader Auto-Levelling Systems |
109 | SAE MA2151-1994 | 1994-03-01 | English | Clamp Assemblies, Saddle or Omega Style, Two Point Mount, Multiple Shapes, Metric |
110 | SAE ARP4776-1994 | 1994-03-01 | English | Pallet/Container Loader Auto-Levelling Systems |
111 | SAE ARP824-1994 | 1994-03-01 | English | HOSE ASSEMBLIES,FLEXIBLE METAL,HIGH-PRESS. & TEMP. |
112 | SAE AMS3797B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots DoD Adopted |
113 | SAE AMS3797/6B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/16 (27) Wide, 6000 (26,689) Breaking Strength DoD Adopted |
114 | SAE AMS3797/7B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/16 (27) Wide, 7000 (31,138) Breaking Strength DoD Adopted |
115 | SAE AMS3797/5B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1 (25) Wide, 5000 (22,241) Breaking Strength DoD Adopted |
116 | SAE AMS3797/11B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/8 (29) Wide, 11,000 (48,930) Breaking Strength DoD Adopted |
117 | SAE AMS3797/3B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1 (25) Wide, 3000 (13,345) Breaking Strength DoD Adopted |
118 | SAE AMS3797/12B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/8 (29) Wide, 12,000 (53,379) Breaking Strength DoD Adopted |
119 | SAE AMS3797/9B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/8 (29) Wide, 9000 (40,034) Breaking Strength DoD Adopted |
120 | SAE AMS3797/4B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1 (25) Wide, 4000 (17,793) Breaking Strength DoD Adopted |
121 | SAE AMS3797/8B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/16 (27) Wide, 8000 (35,586) Breaking Strength DoD Adopted |
122 | SAE AMS3797/2B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 5/8 (15.9) Wide, 2000 (8896) Breaking Strength DoD Adopted |
123 | SAE AMS3797/1B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 5/8 (15.9) Wide, 1000 (4448) Breaking Strength DoD Adopted |
124 | SAE AMS3797/10B-1994 | 1994-03-01 | English | Webbing, Nylon, Integral Locking Slots 1-1/8 (29) Wide, 10,000 (44,482) Breaking Strength DoD Adopted |
125 | SAE AMS1475C-1994 | 1994-03-01 | English | Deodorant, Aircraft Toilet, Formaldehyde Base |
126 | SAE J123-1994 | 1994-03-01 | English | (R) Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications DoD Adopted | ANSI Approved |
127 | SAE J2066-1994 | 1994-02-09 | English | Filter and Filter Element for Hydraulic System(s) Used on Manufacturing and Assembly Equipment, Standard |
128 | SAE J1511-1994 | 1994-02-07 | English | Steering for Off-Road, Rubber-Tired Machines - WITHDRAWN; NO LONGER AVAILABLE |
129 | SAE J1651-1994 | 1994-02-07 | English | Metric Yoke Type Rod Ends, Standard |
130 | SAE J1142-1994 | 1994-02-02 | English | (R) Towability Design Criteria and Equipment Use - Passenger Cars, Vans, and Light-Duty Trucks, Recommended Practice |
131 | SAE AIR4762-1994 | 1994-02-01(R 2014) | English | Compilation of Freezing Brake Experience and Suggested Designs and Operating Procedures Required to Prevent Its Occurrence |
132 | SAE AMS3898/5B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Polyethylene Coated Paper, Perforated 0.0035 inch (0.089 mm)(DoD Adopted) |
133 | SAE AMS3898/6A-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Differentially Coated Paper, Unperforated 0.0035 inch (0.081 mm) |
134 | SAE AMS3898/7A-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Differentially Coated Paper, Unperforated 0.0042 inch (0.107 mm) |
135 | SAE AMS3898/8A-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape/Broadgoods Kraft, Differentially Coated Paper, Unperforated 0.0038 inch ± 0.0004 (0.097 mm ± 0.010) |
136 | SAE AMS3898/9A-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape/Broadgoods Kraft, Differentially Coated Paper, Unperforated 0.0050 inch ± 0.0005 (0.127 mm ± 0.013) |
137 | SAE AMS3898B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape or Broadgoods Paper, 0.004 inch (0.10 mm), Perforated(DoD Adopted) |
138 | SAE AMS3898/1B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Parchment, 0.004 inch (0.10 mm), Unperforated(DoD Adopted) |
139 | SAE AMS3898/4B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Paper, 0.04 inch (0.10 mm), Perforated(DoD Adopted) |
140 | SAE AMS3898/2B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Polyethylene Film, 0.0018 inch (0.046 mm), Unperforated(DoD Adopted) |
141 | SAE AMS3898/3B-1994 | 1994-02-01(R 2014) | English | Interleaf Carrier Material, Composite Tape Polyethylene Coated Paper, Unperforated 0.0035 inch (0.089 mm)(DoD Adopted) |
142 | SAE AS4774A-1994 | 1994-02-01(R 2013) | English | HOSE, AIR DUCT, FLEXIBLE, SILICONE-COATED FABRIC, 1 PSI, EXTERNAL NYLON HELIX, SELF-EXTINGUISHING |
143 | SAE ARP1987A-1994 | 1994-02-01(R 2013) | English | Titles, SAE G-3 Committee Document, Selection of |
144 | SAE AIR4762-1994 | 1994-02-01(R 2010) | English | Compilation of Freezing Brake Experience and Suggested Designs and Operating Procedures Required to Prevent Its Occurrence |
145 | SAE AIR1780A-1994 | 1994-02-01(R 2010) | English | Aircraft Flotation Analysis |
146 | SAE AS639-1994 | 1994-02-01(R 2007) | English | Hose, Polytetrafluoroethylene, Metal Braid, Medium Pressure, Hydraulic, 450 Degrees F |
147 | SAE J1111-1994 | 1994-02-01(R 2007) | English | Component Nomenclature - Skidder-Grapple |
148 | SAE AMS3898B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape or Broadgoods Paper, 0.004 Inch (0.10 mm), Perforated DoD Adopted |
149 | SAE AMS3898/3B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Polyethylene Coated Paper, Unperforated 0.0035 inch (0.089 mm) DoD Adopted |
150 | SAE AMS3898/1B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Parchment, 0.004 inch (0.10 mm), Unperforated DoD Adopted |
151 | SAE AMS3898/4B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Paper, 0.004 inch (0.10 mm), Perforated DoD Adopted |
152 | SAE AMS3898/6A-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Differentially Coated Paper, Unperforated 0.0032 inch (0.081 mm) |
153 | SAE AMS3898/7A-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Differentially Coated Paper, Unperforated 0.0042 in. (0.107 mm) |
154 | SAE AMS3898/8A-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape/Broadgoods Kraft, Differentially Coated Paper, Unperforated 0.0038 inch 卤 0.0004 (0.097 mm 卤 0.010) |
155 | SAE AMS3898/9A-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape/Broadgoods Kraft, Differentially Coated Paper, Unperforated 0.0050 inch 卤 0.0005 (0.127 mm 卤 0.013) |
156 | SAE AMS3898/2B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Polyethylene Film, 0.0018 inch (0.046 mm), Unperforated DoD Adopted |
157 | SAE AMS3898/5B-1994 | 1994-02-01(R 2005) | English | Interleaf Carrier Material, Composite Tape Polyethylene Coated Paper, Perforated 0.0035 inch (0.089 mm) DoD Adopted |
158 | SAE AS4774A-1994 | 1994-02-01(R 2004) | English | Hose, Air Duct, Flexible, Silicone-Coated Fabric, 1 psi, External Nylon Helix, Self-Extinguishing |
159 | SAE ARP1987A-1994 | 1994-02-01(R 2004) | English | Titles, SAE G-3 Committee Document, Selection of |
160 | SAE AMS3611D-1994 | 1994-02-01(R 2003) | English | Plastic Sheet, Polycarbonate General Purpose DoD Adopted |
161 | SAE AMS2629B-1994 | 1994-02-01(R 2001) | English | Fluid, Jet Reference DoD Adopted |
162 | SAE J1608-1994 | 1994-02-01(R 2001) | English | Manual Transmission Shift Patterns |
163 | SAE AIR4791-1994 | 1994-02-01 | English | HUMAN ENGINEERING RECOMMENDATIONS FOR DATA LINK SYSTEMS |
164 | SAE J1111-1994 | 1994-02-01 | English | Component Nomenclature - Skidder-Grapple |
165 | SAE AMS1448A-1994 | 1994-02-01 | English | Sand, Airport Snow and Ice Control ANSI Approved |
166 | SAE AS639-1994 | 1994-02-01 | English | HOSE, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, HYDRAULIC, 450 F |
167 | SAE J1616-1994 | 1994-02-01 | English | Recommended Practice for Compressed Natural Gas Vehicle Fuel, Recommended Practice |
168 | SAE AIR4152-1994 | 1994-02-01 | English | Reciprocating Engine Pneumatic Starters |
169 | SAE AIR1780A-1994 | 1994-02-01 | English | Aircraft Flotation Analysis |
170 | SAE ARP571C-1994 | 1994-02-01 | English | FLIGHT DECK CONTROLS AND DISPLAYS FOR COMMUNICATION |
171 | SAE AIR1780A-1994 | 1994-02-01 | English | Aircraft Flotation Analysis |
172 | SAE AMS3844B-1994 | 1994-02-01 | English | Cloth, Type "E" Glass, Style 7781 Fabric Hot- Melt, Addition-Type, Polyimide Resin Impregnated ANSI Approved |
173 | SAE AMS3849B-1994 | 1994-02-01 | English | Cloth, Quartz, Style 581 Fabric Hot-Melt, Addition-Type, Polyimide Resin Impregnated |
174 | SAE AS580B-1994 | 1994-02-01 | English | PILOT VISIBILITY FROM THE FLIGHT DECK DESIGN |
175 | SAE AMS3348C-1994 | 1994-01-01(R 2007) | English | Silicone (VMQ) Rubber 1150 psi (7.93 MPa) Tensile Strength, High Resiliency 25 - 35 DoD Adopted |
176 | SAE AS1501C-1994 | 1994-01-01(R 2004) | English | HOSE, AIR DUCT, FLEXIBLE, NONMETALLIC, AIRCRAFT |
177 | SAE MA2256A-1994 | 1994-01-01(R 2004) | English | Ferrule, Coupling, Flexible, Variable Cavity, Threaded, Ferrule Tube End, Metric |
178 | SAE MA2251A-1994 | 1994-01-01(R 2004) | English | Coupling, Flexible, Variable Cavity, Threaded Ferrule Type Tube Ends, Envelope Dimensions, Design Standard, Metric |
179 | SAE AS954E-1994 | 1994-01-01(R 2004) | English | Wrenches, Hand Twelve Point High Strength, Thin Wall DoD Adopted |
180 | SAE MA2112B-1994 | 1994-01-01(R 2004) | English | Adapter, Assembly - Port Connection Ring Locked to 24 Degree Flareless Tube End, Metric |
181 | SAE AMS1375B-1994 | 1994-01-01(R 2004) | English | Remover, Paint, Epoxy and Polyurethane Paint Systems |
182 | SAE MA2113B-1994 | 1994-01-01(R 2004) | English | Adapter, Assembly - Port Connection Ring Locked to 60 Degrees Flareless Tube End, Metric |
183 | SAE MA2251A-1994 | 1994-01-01 | English | Coupling, Flexible, Variable Cavity, Threaded Ferrule Type Tube Ends, Envelope Dimensions, Design Standard, Metric |
184 | SAE AMS1375B-1994 | 1994-01-01 | English | Remover, Paint Epoxy and Polyurethane Paint Systems |
185 | SAE J178-1994 | 1994-01-01 | English | (R) Music Steel Spring Wire and Springs, Recommended Practice ANSI Approved |
186 | SAE J382-1994 | 1994-01-01 | English | (R) Windshield Defrosting Systems Performance Requirements - Trucks, Buses, and Multipurpose Vehicles DoD Adopted | ANSI Approved |
187 | SAE M-117-1994 | 1994-01-01 | English | Design Guide for Involute Splines |
188 | SAE MA2256A-1994 | 1994-01-01 | English | Ferrule, Coupling, Flexible, Variable Cavity, Threaded, Ferrule Tube End, Metric |
189 | SAE AMS2399A-1994 | 1994-01-01 | English | Electroless Nickel-Boron Plating - Reaffirmed Noncurrent May 2005 |
190 | SAE J2019-1994 | 1994-01-01 | English | Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus, Standard |
191 | SAE J128-1994 | 1994-01-01 | English | (R) Occupant Restraint System Evaluation - Passenger Cars and Light-Duty Trucks |
192 | SAE J823-1994 | 1994-01-01 | English | Flasher Test, Standard |
193 | SAE J1689-1994 | 1994-01-01 | English | Hydraulic Power Units Used on Machine Tools and Equipment for the Automotive Industry, Standard - November 1994 |
194 | SAE HS-1576-1994 | 1994-01-01 | English | SAE Manual for Incorporating Pnuematic Springs in Vehicle Suspension Designs - 1994 Edition |
195 | SAE J1143-1994 | 1994-01-01 | English | (R) Towed Vehicle/Tow Equipment Attachment Test Procedure - Passenger Cars, Vans, and Light Duty Trucks, Recommended Practice |
196 | SAE HRP 4538-1993 | 1993-12-01 | English | SELECTION OF HYDRAULIC DIRECTIONAL CONTROL VALVES FOR MARINE VEHICLE APPLICATIONS |
197 | SAE J1617-1993 | 1993-11-02 | English | Body Corrosion - A Comprehensive Introduction, Information Report |
198 | SAE AIR1266A-1993 | 1993-11-01(R 2011) | English | Fault Isolation in Environmental Control Systems of Commercial Transports |
199 | SAE AIR1266A-1993 | 1993-11-01(R 2006) | English | Fault Isolation in Environmental Control Systems of Commercial Transports |
200 | SAE MA2263-1993 | 1993-11-01(R 2004) | English | Ferrule, Sleeve, Swaged, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Metric |
201 | SAE MA2262-1993 | 1993-11-01(R 2004) | English | Ferrule, Sleeve, Butt Weld, Threadless Coupling, Flexible, Fixed Cavity, Self- Bolding, Metric |
202 | SAE MA2244-1993 | 1993-11-01(R 2004) | English | Ferrule End, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Design Standard, Metric |
203 | SAE MA2245-1993 | 1993-11-01(R 2004) | English | Ferrule, Butt Weld, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Metric |
204 | SAE MA2243-1993 | 1993-11-01(R 2004) | English | Ferrule, Swaged, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Metric |
205 | SAE MA2246-1993 | 1993-11-01(R 2004) | English | Sleeve End, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Design Standard, Metric |
206 | SAE MA2242-1993 | 1993-11-01(R 2004) | English | Assembled Coupling, Threadless - Flexible, Fixed Cavity, Self-Bonding, Envelope Dimensions, Metric |
207 | SAE MA2241-1993 | 1993-11-01(R 2004) | English | Coupling Assembly, Threadless, Flexible, Fixed Cavity, Self-Bonding, Metric |
208 | SAE ARP1348A-1993 | 1993-11-01(R 2002) | English | Baggage/Cargo Trailer Requirements |
209 | SAE MA2241-1993 | 1993-11-01 | English | Coupling Assembly, Threadless, Flexible, Fixed Cavity, Self-Bonding, Metric |
210 | SAE MA2242-1993 | 1993-11-01 | English | Assembled Coupling, Threadless - Flexible, Fixed Cavity, Self-Bonding, Envelope Dimensions, Metric |
211 | SAE MA2244-1993 | 1993-11-01 | English | Ferrule End, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Design Standard, Metric |
212 | SAE MA2243-1993 | 1993-11-01 | English | Ferrule, Swaged, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Metric |
213 | SAE MA2246-1993 | 1993-11-01 | English | Sleeve End, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Design Standard, Metric |
214 | SAE MA2245-1993 | 1993-11-01 | English | Ferrule, Butt Weld, Threadless Coupling, Flexible, Fixed Cavity, Self-Bonding, Metric |
215 | SAE R-125-1993 | 1993-11-01 | English | Motor Truck Engineering Handbook - Fourth Edition; To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
216 | SAE J539-1993 | 1993-11-01 | English | Voltages for Diesel Electrical Systems |
217 | SAE AMS3705A-1993 | 1993-10-01(R 2014) | English | Epoxy Resin, Cycloaliphatic Liquid |
218 | SAE AMS3388D-1993 | 1993-10-01(R 2012) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber Single Wire Braid Reinforced, Chloroprene Covered, Noncollapsing |
219 | SAE AMS3389D-1993 | 1993-10-01(R 2012) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber Double Wire Braid Reinforced, Chloroprene Covered, Noncollapsing |
220 | SAE AMS3387E-1993 | 1993-10-01(R 2012) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber Textile Reinforced, Chloroprene Covered Noncollapsing |
221 | SAE AMS3386D-1993 | 1993-10-01(R 2012) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber, Textile Reinforced, Chloroprene Covered, Collapsing |
222 | SAE AMS3349C-1993 | 1993-10-01(R 2007) | English | Silicone (VMQ) Rubber 1100 psi (7.58 MPa) Tensile Strength, High Resiliency 65 - 75 DoD Adopted |
223 | SAE AMS3387E-1993 | 1993-10-01(R 2007) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber Textile Reinforced, Chloroprene Covered Noncollapsing |
224 | SAE AMS3388D-1993 | 1993-10-01(R 2007) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber Single Wire Braid Reinforced, Chloroprene Covered, Noncollapsing |
225 | SAE AMS3389D-1993 | 1993-10-01(R 2007) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber, Double Wire Braid Reinforced, Chloroprene Covered, Noncollapsing |
226 | SAE AMS3386D-1993 | 1993-10-01(R 2007) | English | Hose, Aircraft Fueling, Acrylonitrile Butadiene (NBR) Rubber, Textile Reinforced, Chloroprene Covered, Collapsing |
227 | SAE AMS3570E-1993 | 1993-10-01(R 2001) | English | Foam, Flexible Polyurethane Open Cell, Medium Flexibility DoD Adopted |
228 | SAE AMS3377-1993 | 1993-10-01(R 2000) | English | Sealing Compound, Electrically Conductive Corrosion Inhibiting |
229 | SAE AMS3091C-1993 | 1993-10-01(R 2000) | English | Mold Release Agent |
230 | SAE AMS3240J-1993 | 1993-10-01(R 1999) | English | Chloroprene (CR) Rubber Weather Resistant 35 - 45 DoD Adopted |
231 | SAE AMS3242G-1993 | 1993-10-01(R 1999) | English | Chloroprene (CR) Rubber Weather Resistant 75 - 85 |
232 | SAE AMS3241H-1993 | 1993-10-01(R 1999) | English | Chloroprene (CR) Rubber Weather Resistant 55 - 65 DoD Adopted |
233 | SAE AMS3249C-1993 | 1993-10-01(R 1998) | English | Ethylene Propylene (EPDM) Rubber Hydrazine-Base-Fluid Resistant 75 - 85 DoD Adopted |
234 | SAE AMS3828C-1993 | 1993-10-01(R 1998) | English | Glass Roving, Epoxy Resin Preimpregnated Type E Glass |
235 | SAE AMS3817D-1993 | 1993-10-01(R 1998) | English | Nylon Braid, Flat Electrical Tying Resin Coated DoD Adopted |
236 | SAE AMS3829B-1993 | 1993-10-01(R 1998) | English | Cloth, Type "E"-Glass, Style 7781 Fabric Solution-Addition-Type PMR-15 Polyimide Resin Impregnated |
237 | SAE AMS3704A-1993 | 1993-10-01(R 1998) | English | Adhesive, Contact Polychloroprene (CR) Rubber, Resin Modified |
238 | SAE AMS3899B-1993 | 1993-10-01(R 1998) | English | Carbon Fiber Tape and Sheet Polysulfone Resin Impregnated |
239 | SAE AMS3705A-1993 | 1993-10-01(R 1998) | English | Epoxy Resin, Cycloaliphatic Liquid |
240 | SAE AMS7250F-1993 | 1993-10-01(R 1995) | English | NUTS, SELF-LOCKING, STEEL, CORROSION AND HEAT RESISTANT HIGH STRENGTH, ALL METAL 1200 DEGREES F (650 DEGREES C) USE, UNIFIED (MIL-S-7742) THREAD FORM |
241 | SAE AMS3899/2B-1993 | 1993-10-01(R 1994) | English | Carbon Fiber Tape and Sheet Polysulfone Resin Impregnated C PS 140 (965) Tensile, 27 (186) Modulus, 120 (248) |
242 | SAE AMS3899/1B-1993 | 1993-10-01(R 1994) | English | Carbon Fiber Tape and Sheet Polysulfone Resin Impregnated C PS 172 (1170) Tensile, 16 (110) Modulus, 120 (248) |
243 | SAE AMS7283C-1993 | 1993-10-01 | English | GASKETS, TYPE XX ENGINE ACCESSORY DRIVE CORROSION RESISTANT STEEL SCREEN REINFORCED CONTROLLED PERFORMANCE |
244 | SAE AMS7330B-1993 | 1993-10-01 | English | RETAINING RINGS, STEEL, CORROSION RESISTANT SPIRAL WOUND |
245 | SAE AMS7325F-1993 | 1993-10-01 | English | RINGS, SEALING, TUBULAR METAL, CORROSION AND HEAT RESISTANT STEEL |
246 | SAE AMS7475B-1993 | 1993-10-01 | English | BOLTS AND SCREWS, WORK-STRENGTHENED CORROSION AND HEAT RESISTANT ALLOY FORGED HEAD, ROLL THREADED AFTER AGING |
247 | SAE AMS7474C-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION RESISTANT STEEL UPSET HEADED, HEAT TREATED, ROLL THREADED |
248 | SAE AMS7473F-1993 | 1993-10-01 | English | Bolts and Screws, Carbon Steels, Alloy Steels or Corrosion and heat Resistant Steels or Alloys Roll threaded DoD Adopted |
249 | SAE AMS7472K-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION RESISTANT STEEL ROLL THREADED DoD Adopted |
250 | SAE AMS7452M-1993 | 1993-10-01 | English | BOLTS AND SCREWS, LOW-ALLOY STEEL HEAT TREATED, ROLL THREADED |
251 | SAE AMS7471G-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT NICKEL ALLOY UPSET HEADED, HEAT TREATED, ROLL THREADED 1950 DEGREES F (1066 DEGREES C) SOLUTION HEAT TREATED |
252 | SAE AMS7470H-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT STEEL HEAT TREATED, ROLL THREADED |
253 | SAE AMS7468B-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION-RESISTANT WORK-STRENGTHENED ALLOY FORGED HEAD, ROLL THREADED AFTER AGING |
254 | SAE AMS7246B-1993 | 1993-10-01 | English | INSERTS, THREAD FORM, CORROSION AND HEAT RESISTANT ALLOY 72Ni - 15.5Cr - 0.95(Cb+Ta) - 2.5Ti - 0.70Al - 7.0Fe |
255 | SAE AMS7467C-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT NICKEL ALLOY UPSET HEADED, ROLL THREADED, STRESS-RUPTURE RESISTANT |
256 | SAE AMS7466B-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT NICKEL ALLOY UPSET HEADED, ROLL THREADED, FATIGUE RESISTANT |
257 | SAE AMS7251E-1993 | 1993-10-01 | English | NUTS, SELF-LOCKING, CORROSION AND HEAT RESISTANT STEEL HIGH STRENGTH, ALL METAL 1200 DEGREES F (650 DEGREES C) USE, UNIFIED "J" (MIL-S-8879) THREAD FORM |
258 | SAE AMS7461E-1993 | 1993-10-01 | English | BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V UPSET HEADED, HEAT TREATED, ROLL THREADED |
259 | SAE AMS7460F-1993 | 1993-10-01 | English | BOLTS AND SCREWS, TITANIUM ALLOY 6Al - 4V HEAT TREATED, ROLL THREADED |
260 | SAE AMS7459E-1993 | 1993-10-01 | English | Bolts and Screws, Low-Alloy, Heat Resistant Steel Hardened and Tempered, Roll Threaded 195,000 psi (1344 MPa) Tensile Strength - UNS K14675 DoD Adopted |
261 | SAE AMS7252D-1993 | 1993-10-01 | English | NUTS, SELF-LOCKING, STEEL HIGH STRENGTH, ALL METAL 450 DEGREES F (230 DEGREES C) USE, UNIFIED "J" (MIL-S-8879) THREAD FORM |
262 | SAE AMS7458G-1993 | 1993-10-01 | English | STUDS, LOW-ALLOY HEAT-RESISTANT STEEL NORMALIZED AND TEMPERED, ROLL THREADED 135,000 psi (931 MPa) TENSILE STRENGTH |
263 | SAE AMS7456K-1993 | 1993-10-01 | English | STUDS, LOW-ALLOY STEEL HEAT TREATED, ROLLED THREADED |
264 | SAE AMS7478J-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT STEEL HEAT TREATED, ROLL THREADED 1800 DEGREES F (982 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
265 | SAE AMS7455G-1993 | 1993-10-01 | English | BOLTS AND SCREWS, LOW-ALLOY STEEL, HEAT-RESISTANT HARDENED AND TEMPERED, ROLL THREADED |
266 | SAE AMS7479E-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT STEEL HEAT TREATED, ROLL THREADED 1650 DEGREES F (899 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
267 | SAE AMS7477D-1993 | 1993-10-01 | English | BOLTS AND SCREWS, CORROSION AND HEAT RESISTANT STEEL UPSET HEADED, HEAT TREATED, ROLL THREADED 1800 DEGREES F(982 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
268 | SAE AMS7481C-1993 | 1993-10-01 | English | STUDS, CORROSION AND HEAT RESISTANT STEEL HEAT TREATED, ROLL THREADED |
269 | SAE MAM7211C-1993 | 1993-10-01 | English | COTTER PINS, METRIC, CORROSION AND HEAT RESISTANT STEEL 18Cr - 10.5Ni - 0.40Ti |
270 | SAE J1563-1993 | 1993-10-01 | English | (R) Guidelines for Laboratory Cyclic Corrosion Test Procedures for Painted Automotive Parts, Information Report |
271 | SAE AMS1426C-1993 | 1993-10-01 | English | Fluid, Deicing/Anti-Icing, Runways and Taxiways Glycol Base DoD Adopted |
272 | SAE AMS7211G-1993 | 1993-10-01 | English | COTTER PINS, STEEL, CORROSION AND HEAT RESISTANT 18Cr - 10.5Ni - 0.40Ti |
273 | SAE AMS7225G-1993 | 1993-10-01 | English | RIVETS, CARBON STEEL |
274 | SAE AMS7229H-1993 | 1993-10-01 | English | RIVETS, CORROSION AND HEAT RESISTANT STEEL 18Cr - 10.5Ni - 0.70 (Cb+Ta) SOLUTION HEAT TREATED |
275 | SAE AMS7222E-1993 | 1993-10-01 | English | RIVETS, ALUMINUM ALLOY 2.5Cu - 0.35Mg (2117-T4) |
276 | SAE AMS7207H-1993 | 1993-10-01 | English | SPRING PINS, TUBULAR CORROSION AND MODERATE HEAT RESISTANT STEEL |
277 | SAE AMS7228J-1993 | 1993-10-01 | English | RIVETS, CORROSION RESISTANT STEEL 18Cr - 9Ni SOLUTION HEAT TREATED |
278 | SAE AMS7210H-1993 | 1993-10-01 | English | COTTER PINS, STEEL, CORROSION-RESISTANT 18Cr-9.5Ni |
279 | SAE AMS7220E-1993 | 1993-10-01 | English | ALUMINUM RIVETS 99Al (1100-H14) |
280 | SAE ARP4102/10A-1993 | 1993-09-03(R 2007) | English | Collision Avoidance System ANSI Approved |
281 | SAE AIR1569A-1993 | 1993-09-01(R 2014) | English | Handling and Installation Practice for Aerospace Hose Assemblies |
282 | SAE J1051-1993 | 1993-09-01(R 2013) | English | Force-Deflection Measurements of Cushioned Components of Seats for Off-Road Work Machines |
283 | SAE ARP1185B-1993 | 1993-09-01(R 2013) | English | Flexure Testing of Hydraulic Tubing Joints and Fittings |
284 | SAE ARP1258B-1993 | 1993-09-01(R 2013) | English | Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements |
285 | SAE MA3513-1993 | 1993-09-01(R 2013) | English | BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC |
286 | SAE ARP1185B-1993 | 1993-09-01(R 2007) | English | Flexure Testing of Hydraulic Tubing Joints and Fittings DoD Adopted |
287 | SAE ARP4102/7 APPENDIX C-1993 | 1993-09-01(R 2007) | English | Appendix C Electronic Display Symbology for Engine Displays |
288 | SAE AIR1569A-1993 | 1993-09-01(R 2007) | English | Handling and Installation Practice for Aerospace Hose Assemblies |
289 | SAE MA3512-1993 | 1993-09-01(R 2004) | English | BOLT, MACHINE - SPLINE DRIVE HD, CLOSE TOL FULL SHANK, UNS N07001, METRIC |
290 | SAE ARP1258B-1993 | 1993-09-01(R 2004) | English | Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements |
291 | SAE MA4534-1993 | 1993-09-01(R 2004) | English | Socket Wrenches, Hand (Metric) DoD Adopted |
292 | SAE MA3513-1993 | 1993-09-01(R 2004) | English | BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC |
293 | SAE MA3512-1993 | 1993-09-01(R 2004) | English | BOLT, MACHINE - SPLINE DRIVE HD, CLOSE TOL FULL SHANK, UNS N07001, METRIC |
294 | SAE J254-1993 | 1993-09-01 | English | (R) Instrumentation and Techniques for Exhaust Gas Emissions Measurement ANSI Approved |
295 | SAE J2179-1993 | 1993-09-01 | English | A Test for Evaluating the Rearward Amplification of Multi-Articulated Vehicles |
296 | SAE J1692-1993 | 1993-08-30 | English | Valve Seat Insert Information Report, Information Report |
297 | SAE AS4330-1993 | 1993-08-24(R 2005) | English | TUBING, FLARED, STANDARD DIMENSIONS FOR, DESIGN STANDARD DoD Adopted |
298 | SAE ARP4048-1993 | 1993-08-17(R 2011) | English | BALANCING MACHINES - DESCRIPTION AND EVALUATION HORIZONTAL, TWO-PLANE, HARD-BEARING TYPE FOR GAS TURBINE ROTORS ANSI Approved |
299 | SAE AS4073-1993 | 1993-08-17(R 2000) | English | Air Cycle Air Conditioning Systems for Military Air Vehicles ANSI Approved |
300 | SAE ARP4048-1993 | 1993-08-17 | English | Balancing Machines - Description and Evaluation Horizontal, Two-Plane, Hard-Bearing Type for Gas Turbine Rotors ANSI Approved |
301 | SAE ARP4048-1993 | 1993-08-17 | English | Balancing Machines - Description and Evaluation Horizontal, Two-Plane, Hard-Bearing Type for Gas Turbine Rotors |
302 | SAE AS4679B-1993 | 1993-08-01(R 2013) | English | WASHER, FLAT, SHORT FLARELESS |
303 | SAE AS4347-1993 | 1993-08-01(R 2013) | English | UNION ASSEMBLY, DOUBLE RETAINED NUT |
304 | SAE AS4312-1993 | 1993-08-01(R 2007) | English | TEE, FLARED TUBE WITH PIPE THREAD ON RUN, FOR SEAL RING |
305 | SAE AS4324-1993 | 1993-08-01(R 2007) | English | Washer, Flared Tube Fitting Adjutable End, Design Standard |
306 | SAE AS4325-1993 | 1993-08-01(R 2007) | English | Fitting End, Conical, Standard Dimensions for, Design Standard |
307 | SAE AS4326-1993 | 1993-08-01(R 2007) | English | Nut, Coupling |
308 | SAE AS4302-1993 | 1993-08-01(R 2007) | English | Tee Assembly, Flared Tube, Retained Nut on Run, for Seal Ring |
309 | SAE AS4303-1993 | 1993-08-01(R 2007) | English | Elbow Assembly 90 Degree, Flared Tube to Adjustable End, for Seal Ring |
310 | SAE AS4327-1993 | 1993-08-01(R 2007) | English | Sleeve, Flared Tube Fitting |
311 | SAE AS4316-1993 | 1993-08-01(R 2007) | English | Elbow Assembly 45掳, Flared Tube to Retained Nut, for Seal Ring |
312 | SAE AS4320-1993 | 1993-08-01(R 2007) | English | Fitting End, Straight Thread, Standard Dimensions for, Design Standard |
313 | SAE AS4329-1993 | 1993-08-01(R 2007) | English | Cap Assembly, Pressure Seal Flared Tube Fitting |
314 | SAE AS4314-1993 | 1993-08-01(R 2007) | English | ELBOW ASSEMBLY 45掳, FLARED TUBE TO ADJUSTABLE END, FOR SEAL RING |
315 | SAE AS4321-1993 | 1993-08-01(R 2007) | English | Fitting End, Internal Flare, Single Angle, Standard Dimensions for, Design Standard |
316 | SAE AS4322-1993 | 1993-08-01(R 2007) | English | Fitting End, Adjustable, Standard Dimensions for, Design Standard |
317 | SAE AS4341-1993 | 1993-08-01(R 2007) | English | Wire, Retaining for Retained Nut |
318 | SAE AS4346-1993 | 1993-08-01(R 2007) | English | Union Assembly, Adjustable End |
319 | SAE AS4311-1993 | 1993-08-01(R 2007) | English | Tee, Flared Tube, Internal Thread on Side, for Seal Ring |
320 | SAE AS4304-1993 | 1993-08-01(R 2007) | English | Tee Assembly, Flared Tube, Retained Nut on Side, for Seal Ring |
321 | SAE AS4348-1993 | 1993-08-01(R 2007) | English | Adapter Assembly, Retained Nut to Boss |
322 | SAE AS4306-1993 | 1993-08-01(R 2007) | English | Tee Assembly, Flared Tube, Adjustable End on Side, for Seal Ring |
323 | SAE AS4349-1993 | 1993-08-01(R 2007) | English | Coupling, Tube |
324 | SAE AS4350-1993 | 1993-08-01(R 2007) | English | Plug, Hex Head |
325 | SAE AS4315-1993 | 1993-08-01(R 2007) | English | Elbow Assembly 90掳, Flared Tube to Retained Nut, for Seal Ring |
326 | SAE AS4313-1993 | 1993-08-01(R 2007) | English | Tee, Flared Tube with Pipe Thread on Side, for Seal Ring |
327 | SAE AS4310-1993 | 1993-08-01(R 2007) | English | Tee, Flared Tube, Internal Thread on Run, for Seal Ring |
328 | SAE AS4305-1993 | 1993-08-01(R 2007) | English | Tee Assembly, Flared Tube, Adjustable End on Run, for Seal Ring |
329 | SAE AS4323-1993 | 1993-08-01(R 2007) | English | Nut, Retained, for Flared Tube Fittings |
330 | SAE AMS5550E-1993 | 1993-08-01(R 2006) | English | Alloy Sheet, Strip, and Plate, Corrosion and Heat Resistant 80Ni - 15.5Cr - 0.62ti - 3.25Al Annealed |
331 | SAE AS965B-1993 | 1993-08-01(R 2004) | English | Drive-Studded, Accessory, (203.2) 8.000 BC Round, Design Standard For |
332 | SAE AS967B-1993 | 1993-08-01(R 2004) | English | Drive-Studded, Accessory, (254) 10.000 BC Round, Design Standard For |
333 | SAE AS971B-1993 | 1993-08-01(R 2004) | English | Drive-Accessory, (254) 10.000 BC Round, QAD, Design Standard for DoD Adopted |
334 | SAE AS969B-1993 | 1993-08-01(R 2004) | English | Drive-Accessory, (127) 5.000 BC Round, QAD, Design Standard For |
335 | SAE AS970B-1993 | 1993-08-01(R 2004) | English | Drive-Accessory, (203.2) 8.000 BC Round, QAD, Design Standard for - Best Copy Available DoD Adopted |
336 | SAE AS4347-1993 | 1993-08-01(R 2004) | English | Union Assembly, Double Retained Nut |
337 | SAE AS4679B-1993 | 1993-08-01(R 2004) | English | Washer, Flat, Short Flareless |
338 | SAE AS3485-1993 | 1993-08-01(R 2004) | English | NUT, SELF-LOCKING, 12 POINT, REDUCED HEIGHT, SILVER PLATE, UNS S66286 DoD Adopted |
339 | SAE AS963B-1993 | 1993-08-01(R 2001) | English | Drive-Studded, Accessory, (127) 5.000 BC Round, Design Standard for |
340 | SAE J641-1993 | 1993-08-01(R 2000) | English | Hydrodynamic Drives Terminology ANSI Approved |
341 | SAE J58-1993 | 1993-08-01(R 1998) | English | Flanged 12-Point Screws |
342 | SAE R-122-1993 | 1993-08-01 | English | History of the Electric Automobile Battery-Only Powered Cars - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
343 | SAE R-127-1993 | 1993-08-01 | English | Carriages Without Horses J. Frank Duryea and the Birth of the American Automobile Industry - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
344 | SAE AS4305-1993 | 1993-08-01 | English | TEE ASSEMBLY, FLARED TUBE, ADJUSTABLE END ON RUN, FOR SEAL RING |
345 | SAE AS4329-1993 | 1993-08-01 | English | CAP ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING |
346 | SAE AS4324-1993 | 1993-08-01 | English | WASHER, FLARED TUBE FITTING ADJUSTABLE END, DESIGN STANDARD |
347 | SAE AS4327-1993 | 1993-08-01 | English | SLEEVE, FLARED TUBE FITTING |
348 | SAE AS4346-1993 | 1993-08-01 | English | UNION ASSEMBLY, ADJUSTABLE END |
349 | SAE AS4350-1993 | 1993-08-01 | English | PLUG, HEX HEAD |
350 | SAE AS4348-1993 | 1993-08-01 | English | ADAPTER ASSEMBLY, RETAINED NUT TO BOSS |
351 | SAE AS4322-1993 | 1993-08-01 | English | FITTING END, ADJUSTABLE, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
352 | SAE AS4321-1993 | 1993-08-01 | English | FITTING END, INTERNAL FLARE, SINGLE ANGLE, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
353 | SAE AS4349-1993 | 1993-08-01 | English | COUPLING, TUBE |
354 | SAE AS4315-1993 | 1993-08-01 | English | ELBOW ASSEMBLY 90⁰, FLARED TUBE TO RETAINED NUT, FOR SEAL RING |
355 | SAE ARD50004-1993 | 1993-08-01 | English | OPEN SYSTEMS INTERCONNECTION (OSI) AND OTHER REFERENCE MODELS - USER PERSPECTIVES FOR REAL TIME APPLICATIONS |
356 | SAE AS4325A-1993 | 1993-08-01 | English | Fitting End, Conical, Standard Dimensions for, Design Standard |
357 | SAE AMS3940H-1993 | 1993-07-01(R 2014) | English | Fiberboard, Hard-Pressed, Structural |
358 | SAE AMS3710C-1993 | 1993-07-01(R 2014) | English | Sandwich Structures, Glass Fabric-Resing Low Pressure Molded, Heat Resistant(DoD Adopted) |
359 | SAE AMS3799/3B-1993 | 1993-07-01(R 2006) | English | Webbing, Tubular, Low Modulus Aramid 1 (25) Wide, 4000 (17,793) Breaking Strength DoD Adopted |
360 | SAE AMS3799/1B-1993 | 1993-07-01(R 2006) | English | Webbing, Tubular, Low Modulus Aramid 9/16 (14) Wide, 1400 (6228) Breaking Strength DoD Adopted |
361 | SAE AMS3799/2B-1993 | 1993-07-01(R 2006) | English | Webbing, Tubular, Low Modulus Aramid 3/4 (19) Wide, 2300 (10,231) Breaking Strength DoD Adopted |
362 | SAE AMS3799/4B-1993 | 1993-07-01(R 2006) | English | Webbing, Tubular, Low Modulus Aramid 3-3/16 (81) Wide, 2250 (10,008) Breaking Strength DoD Adopted |
363 | SAE AMS3799B-1993 | 1993-07-01(R 2006) | English | Webbing, Tubular, Low-Modulus Aramid-54 DoD Adopted |
364 | SAE AMS3680C-1993 | 1993-07-01(R 2006) | English | Insulation, Thermal Silica Fiber DoD Adopted |
365 | SAE AMS3568/2A-1993 | 1993-07-01(R 2006) | English | Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing 15 Pounds/Cubic Foot (240 kg/m3) Density DoD Adopted |
366 | SAE AMS3568/1A-1993 | 1993-07-01(R 2006) | English | Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing 5 Pounds/Cubic Foot (80 kg/m3) Density DoD Adopted |
367 | SAE AMS3568/3A-1993 | 1993-07-01(R 2006) | English | Foam, Polyether Urethane (EU) Elastomer, Shock Absorbing 20 Pounds/Cubic Foot (320 kg/m3) Density DoD Adopted |
368 | SAE MA2060A-1993 | 1993-07-01(R 2004) | English | Fittings, Welded, Hydraulic, Titanium and Corrosion Resistant Steel, 21 000 kPa, Metric |
369 | SAE AMS2279A-1993 | 1993-07-01(R 2004) | English | Tolerances Rubber Products |
370 | SAE AMS1385A-1993 | 1993-07-01(R 2004) | English | Compound, Hot Carbon and Paint Remover Aircraft Turbine Engine Components DoD Adopted |
371 | SAE AMS3683A-1993 | 1993-07-01(R 2001) | English | Tubing, Irradiated Modified Fluoropolymer Plastic, Electrical Insulation Flame Resistant, Flexible, Heat-Shrinkable, 2 to 1 Shrink Ratio |
372 | SAE AMS3798/1B-1993 | 1993-07-01(R 1999) | English | Webbing, Low Modulus Aramid 9/16 (14) Wide, 500 (2224) Breaking Strength Herringbone Twill, Resin Treated DoD Adopted |
373 | SAE AMS3798/9B-1993 | 1993-07-01(R 1999) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 6500 (28,913) Breaking Strength Herringbone Twill Resin Treated DoD Adopted |
374 | SAE AMS3798/5B-1993 | 1993-07-01(R 1999) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 3600 (16,014) Breaking Strength Herringbone Twill, Resin Treated DoD Adopted |
375 | SAE AMS3798/2B-1993 | 1993-07-01(R 1999) | English | Webbing, Low Modulus Aramid 1 (25) Wide, 600 (2669) Breaking Strength Herringbone Twill DoD Adopted |
376 | SAE J1419-1993 | 1993-07-01(R 1999) | English | Tapers for Shaft Ends and Hubs for Fuel Injection Pumps |
377 | SAE AMS3940H-1993 | 1993-07-01(R 1999) | English | Fiberboard, Hard-Pressed, Structural |
378 | SAE AMS3798/13B-1993 | 1993-07-01(R 1999) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 7300 (32,472) Breaking Strength Twill, Resin Treated DoD Adopted |
379 | SAE AMS3811B-1993 | 1993-07-01(R 1998) | English | Rods, Aramid Fiber, Polyester Resin Coated Pultrusion |
380 | SAE AMS3798/12B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1 (25) Wide, 9000 (40,034) Breaking Strength Special Weave DoD Adopted |
381 | SAE AMS3798/15B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1 (25) Wide, 2500 (11,121) Breaking Strength Herringbone Twill DoD Adopted |
382 | SAE MAM2279A-1993 | 1993-07-01(R 1998) | English | Tolerances, Metric; Rubber Products ANSI Approved |
383 | SAE AMS3812B-1993 | 1993-07-01(R 1998) | English | Rods, Glass Fiber, Polyester Resin, Coated Pultrusion |
384 | SAE AMS3798B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid DoD Adopted |
385 | SAE AMS3798/14B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1-1/4 (32) Wide, 800 (3,559) Breaking Strength Herringbone Twill DoD Adopted |
386 | SAE AMS3798/7B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 8700 (38,700) Breaking Strength Double Plain Weave with Binder DoD Adopted |
387 | SAE AMS3798/6B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 3-1/32 (77) Wide, 9000 (40,034) Breaking Strength Double Plain Weave with Binder DoD Adopted |
388 | SAE AMS3666D-1993 | 1993-07-01(R 1998) | English | Polytetrafluoroethylene (PTFE) Sheet, Glass Cloth Reinforced DoD Adopted |
389 | SAE AMS3798/4B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 5500 (24,465) Breaking Strength Double Plain Weave with Binder DoD Adopted |
390 | SAE AMS3798/10B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1 (25) Wide, 6000 (26,689) Breaking Strength Herringbone Twill DoD Adopted |
391 | SAE AMS3798/11B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1-3/4 (44) Wide, 10,000 (44,482) Breaking Strength Herringbone Twill DoD Adopted |
392 | SAE AMS3798/3B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 3/4 (19) Wide, 600 (2669) Breaking Strength Herringbone Twill DoD Adopted |
393 | SAE AMS3798/8B-1993 | 1993-07-01(R 1998) | English | Webbing, Low Modulus Aramid 1-23/32 (44) Wide, 1200 (5338) Breaking Strength Herringbone Twill DoD Adopted |
394 | SAE AMS7257C-1993 | 1993-07-01(R 1998) | English | Rings, Sealing, Perfluorocarbon (FFKM) Rubber High Temperature Fluid Resistant 70 - 80 DoD Adopted |
395 | SAE AMS3607F-1993 | 1993-07-01(R 1998) | English | Plastic Sheet Cotton Fabric Reinforced Phenol-Formaldehyde DoD Adopted |
396 | SAE AMS3628D-1993 | 1993-07-01(R 1998) | English | Plastic Extrusions and Moldings, Polycarbonate General Purpose DoD Adopted |
397 | SAE AMS3710C-1993 | 1993-07-01(R 1998) | English | Sandwich Structures, Glass Fabric-Resin Low Pressure Molded, Heat Resistant DoD Adopted |
398 | SAE AMS1385A-1993 | 1993-07-01 | English | Compound, Hot Carbon and Paint Remover Aircraft Turbine Engine Components |
399 | SAE AMS5633D-1993 | 1993-07-01 | English | Alloy Bars and Forgings, Corrosion and Heat Resistant 38Fe - 13.2Cr - 38Ni - 5.5Mo - 0.85Cb - 2.5Ti - 1.6Al - 0.009B Consumable Electrode Melted, Solution Heat Treated, Precipitation Hardenable |
400 | SAE AMS5634C-1993 | 1993-07-01 | English | Alloy Bars and Forgings, Corrosion and Heat Resistant 38Fe - 13.2Cr - 38Ni - 5.5Mo - 0.85Cb - 2.5Ti - 1.6Al - 0.009B Consumable Electrode Melted, Solution and Precipitation Heat Treated |
401 | SAE AMS3623D-1993 | 1993-07-01 | English | Tubing, Irradiated Polychloroprene Elastomer, Electrical Insulation Flexible, Heat-Shrinkable, 1.750 to 1 Shrink Ratio DoD Adopted |
402 | SAE AMS5787B-1993 | 1993-07-01 | English | Alloy Welding Electrodes, Covered, Corrosion and Heat Resistant 63Ni - 5.0Cr - 24.5Mo - 5.5Fe |
403 | SAE AMS3806F-1993 | 1993-07-01 | English | Cloth, Airplane, Mercerized Cotton 80 Pounds Force (356 N) Breaking Strength |
404 | SAE R-135-1993 | 1993-07-01 | English | Designing Cost-Efficient Mechanisms - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
405 | SAE AMS3637F-1993 | 1993-07-01 | English | Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Clear, Flexible, Heat Shrinkable 2 to 1 Shrink Ratio |
406 | SAE AMS3638F-1993 | 1993-07-01 | English | Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Pigmented, Semi-Rigid, Heat Shrinkable, 2 to 1 Shrink Ratio DoD Adopted |
407 | SAE AMS3634D-1993 | 1993-07-01 | English | Tubing, Polyolefin Plastic, Electrical Insulation Selectively Crosslinked, Semi-Rigid, Heat-Shrinkable |
408 | SAE AMS3639F-1993 | 1993-07-01 | English | Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Clear, Semi-Rigid, Heat Shrinkable, 2 to 1 Shrink Ratio |
409 | SAE ARP1195-1993 | 1993-07-01 | English | TURBINE NOZZLE AREA MEASUREMENT BY AIRFLOW METHOD |
410 | SAE J1668-1993 | 1993-06-30(R 1999) | English | Diesel Engines - Fuel Injection Pump Testing |
411 | SAE J1310-1993 | 1993-06-29 | English | Electric Engine Preheaters and Battery Warmers for Diesel Engines, Information Report |
412 | SAE ARP4392-1993 | 1993-06-18(R 2002) | English | Lighting, Aircraft Exterior, Night Vision Imaging System (NVIS) Compatible |
413 | SAE AIR4845-1993 | 1993-06-18 | English | FMECA Process in the Concurrent Engineering (CE) Environment |
414 | SAE AIR1603-1993 | 1993-06-17 | English | Auxiliary Power System Considerations for Advanced Military Aircraft |
415 | SAE AIR4728-1993 | 1993-06-09(R 2013) | English | References, Spacecraft and Spacecraft Servicing, Fluid System Components (Abbreviations, Acronyms, Definitions, Applicable Documents and Environmental Conditions) |
416 | SAE AIR4728-1993 | 1993-06-09(R 2004) | English | References, Spacecraft and Spacecraft Servicing, Fluid System Components (Abbreviations, Acronyms, Definitions, Applicable Documents and Environmental Conditions) |
417 | SAE J1801-1993 | 1993-06-01(R 2014) | English | Brake Effectiveness Marking for Brake Blocks-Truck and Bus |
418 | SAE AS4659A-1993 | 1993-06-01(R 2013) | English | FITTING END, EXTERNAL THREAD, SHORT FLARELESS, DESIGN STANDARD |
419 | SAE J1223-1993 | 1993-06-01(R 2012) | English | Marine Carburetors and Fuel Injection Throttle Bodies |
420 | SAE J561-1993 | 1993-06-01(R 2010) | English | Electrical Terminals鈥擡yelet and Spade Type DoD Adopted |
421 | SAE ARP4104/1-1993 | 1993-06-01(R 2007) | English | Flight Envelope Awareness/Protection |
422 | SAE ARP4102/13A-1993 | 1993-06-01(R 2007) | English | Data Link |
423 | SAE ARP4102/7 APPENDIX B-1993 | 1993-06-01(R 2007) | English | Appendix B Electronic Display Symbology for EHSI/ND |
424 | SAE MA2001B-1993 | 1993-06-01(R 2007) | English | Aerospace Fluid Systems and Components - Pressure and Temperature Classifications |
425 | SAE J1801-1993 | 1993-06-01(R 2007) | English | Brake Effectiveness Marking for Brake Blocks鈥擳ruck and Bus |
426 | SAE MAP2261-1993 | 1993-06-01(R 2007) | English | Fluid Couplings for Spacecraft Servicing, Preparation of Specification for, Metric |
427 | SAE J1223-1993 | 1993-06-01(R 2006) | English | Marine Carburetors and Fuel Injection Throttle Bodies |
428 | SAE J2057-4-1993 | 1993-06-01(R 2006) | English | Class A Multiplexing Architecture Strategies |
429 | SAE J2057-3-1993 | 1993-06-01(R 2006) | English | Class A Multiplexing Sensors |
430 | SAE AS4659A-1993 | 1993-06-01(R 2005) | English | FITTING END, BULKHEAD, EXTERNAL THREAD, SHORT FLARELESS, DESIGN STANDARD |
431 | SAE MAP4296-1993 | 1993-06-01(R 2004) | English | Drawing Interpretations, Standard Machining Practice, Tube Fittings and Connectors, Fluid Systems, Metric |
432 | SAE J1118-1993 | 1993-06-01(R 2002) | English | Hydraulic Valves for Motor Vehicle Brake Systems Test Procedure |
433 | SAE J2228-1993 | 1993-06-01(R 2001) | English | Kingpin Wear Limits - Commercial Trailers and Semitrailers ANSI Approved |
434 | SAE J1568-1993 | 1993-06-01(R 2001) | English | Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders |
435 | SAE J1875-1993 | 1993-06-01(R 2001) | English | Materials for Plastic Check Valves for Vacuum Booster Systems |
436 | SAE J1657-1993 | 1993-06-01(R 1999) | English | Selection Criteria for Retrofit Refrigerants to Replace CFC-12 (R-12) in Mobile Air-Conditioning Systems |
437 | SAE J1659-1993 | 1993-06-01(R 1999) | English | Vehicle Testing Requirements for Replacement Refrigerants for CFC-12 (R-12) Mobile Air-Conditioning Systems |
438 | SAE J1658-1993 | 1993-06-01(R 1999) | English | Alternate Refrigerant Consistency Criteria for Use in Mobile Air-Conditioning Systems |
439 | SAE J1662-1993 | 1993-06-01(R 1998) | English | Compatibility of Retrofit Refrigerants with Air-Conditioning System Materials |
440 | SAE J1660-1993 | 1993-06-01(R 1998) | English | Fittings and Labels for Retrofit of CFC-12 (R-12) Mobile Air-Conditioning Systems to HFC-134a (R-134a) |
441 | SAE J1628-1993 | 1993-06-01(R 1998) | English | Technician Procedure for Using Electronic Refrigerant Leak Detectors for Service of Mobile Air-Conditioning Systems |
442 | SAE J2181-1993 | 1993-06-01(R 1998) | English | Steady-State Circular Test Procedure for Trucks and Buses ANSI Approved |
443 | SAE J2119-1993 | 1993-06-01(R 1997) | English | Manual Controls for Mature Drivers |
444 | SAE J1467-1993 | 1993-06-01 | English | (R) Clip Fastener Fitting, Standard ANSI Approved |
445 | SAE ARP4392-1993 | 1993-06-01 | English | Lighting, Aircraft Exterior, Night Vision Imaging System (NVIS) Compatible |
446 | SAE MA2001B-1993 | 1993-06-01 | English | Aerospace Fluid Systems and Components - Pressure and Temperature Classifications |
447 | SAE J945-1993 | 1993-06-01 | English | (R) Vehicular Hazard Warning Flashers, Standard ANSI Approved |
448 | SAE J726-1993 | 1993-06-01 | English | Air Cleaner Test Code DoD Adopted |
449 | SAE J518-1993 | 1993-06-01 | English | Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Bolt Split Flange Type DoD Adopted | ANSI Approved |
450 | SAE J1974-1993 | 1993-06-01 | English | Decorative Anodizing Specification for Automotive Applications, Recommended Practice ANSI Approved |
451 | SAE TSB 001-1993 | 1993-06-01 | English | SAE Technical Standards Board Rules and Regulations, Technical Report; |
452 | SAE J1615-1993 | 1993-06-01 | English | Thread Sealants |
453 | SAE J1629-1993 | 1993-06-01 | English | Cautionary Statements for Handling HFC-134A During Mobile Air Conditioning Service, Information Report |
454 | SAE J1649/1-1993 | 1993-06-01 | English | Compressed Air for General Use- Part 1: Contaminants and Quality Classes, Standard ANSI Approved |
455 | SAE J1533-1993 | 1993-06-01 | English | Operator Enclosure Air Filter Element Test Procedure, Recommended Practice |
456 | SAE MAP4296-1993 | 1993-06-01 | English | Drawing Interpretations, Standard Machining Practice, Tube Fittings and Connectors, Fluid Systems, Metric |
457 | SAE MAP2261-1993 | 1993-06-01 | English | Fluid Couplings for Spacecraft Servicing, Preparation of Specification for, Metric |
458 | SAE J296-1993 | 1993-06-01 | English | (R) Excavator, Mini-Excavator, and Backhoe Hoe Bucket Volumetric Rating DoD Adopted | ANSI Approved |
459 | SAE J1253-1993 | 1993-06-01 | English | Low-Temperature Cranking Load Requirements of an Engine, Recommended Practice |
460 | SAE J909-1993 | 1993-06-01 | English | (R) Three-Point Hitch, Implement Quick- Attaching Coupler, Agricultural Tractors |
461 | SAE J1012-1993 | 1993-06-01 | English | (R) Operator Enclosure Pressurization System Test Procedure, Recommended Practice |
462 | SAE J715-1993 | 1993-06-01 | English | Three-Point Free-Link Hitch Attachment of Implements to Agricultural Wheeled Tractors, Standard ANSI Approved |
463 | SAE AS4710-1993 | 1993-05-10(R 2006) | English | PI-BUS DoD Adopted |
464 | SAE AIR4065-1993 | 1993-05-07(R 2004) | English | Propeller/Propfan In-Flight Thrust Determination |
465 | SAE AIR4495-1993 | 1993-05-04 | English | Helicopter Powerplant Corrosion Protection |
466 | SAE AS411B-1993 | 1993-05-01(R 2008) | English | Manifold Pressure Indicating Instruments |
467 | SAE AS391C-1993 | 1993-05-01(R 2008) | English | Airspeed Indicator (Pitot Static) (Reciprocating Engine Powered Aircraft) |
468 | SAE AS392C-1993 | 1993-05-01(R 2008) | English | ALTIMETER, PRESSURE ACTUATED SENSITIVE TYPE |
469 | SAE J1635-1993 | 1993-05-01(R 1998) | English | SAE Cold Start and Driveability Procedure ANSI Approved |
470 | SAE ARP1211A-1993 | 1993-05-01 | English | Gas Turbine Engine Status Performance Presentation for Digital Computer Programs DoD Adopted |
471 | SAE AS4703A-1993 | 1993-04-27(R 2004) | English | Fitting End, Acorn, Short Flareless, Design Standard |
472 | SAE J2708-1993 | 1993-04-14 | English | (R) Agricultural Tractor Test Code (OECD) |
473 | SAE AIR4495-1993 | 1993-04-05 | English | Helicopter Powerplant Corrosion Protection |
474 | SAE AS7235-1993 | 1993-04-02(R 2012) | English | Rivets, UNS S66286, Steel, Corrosion and Heat Resistant, 80 ksi Shear Strength, Procurement Specification for |
475 | SAE AS7235-1993 | 1993-04-02(R 2006) | English | Rivets, UNS S66286, Steel, Corrosion and Heat Resistant, 80 ksi Shear Strength, Procurement Specification for DoD Adopted |
476 | SAE AMS3217A-1993 | 1993-04-01(R 2013) | English | Standard Elastomer Stocks Test Slabs |
477 | SAE AS1177A-1993 | 1993-04-01(R 2012) | English | Nondestructive Inspection Standards for Bolts and Screws |
478 | SAE AMS3199K-1993 | 1993-04-01(R 2007) | English | Sponge, Chloroprene (CR) Rubber Firm DoD Adopted | ANSI Approved |
479 | SAE AMS3198K-1993 | 1993-04-01(R 2007) | English | Sponge, Chloroprene (CR) Rubber Medium Stiffness DoD Adopted | ANSI Approved |
480 | SAE AMS3647C-1993 | 1993-04-01(R 2006) | English | Polyfluoroethylene Propylene Film and Sheet DoD Adopted |
481 | SAE AMS3679B-1993 | 1993-04-01(R 2006) | English | Insulation, Thermal Ceramic Fiber DoD Adopted |
482 | SAE AS1177A-1993 | 1993-04-01(R 2006) | English | Nondestructive Inspection Standards for Bolts and Screws DoD Adopted |
483 | SAE AMS3655B-1993 | 1993-04-01(R 1999) | English | Tubing, Electrical Insulation Thin Wall, Extruded Polytetrafluoroethylene (PTFE) DoD Adopted |
484 | SAE AMS3212N-1993 | 1993-04-01(R 1998) | English | Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistant 55 - 65 DoD Adopted | ANSI Approved |
485 | SAE AMS3217/4A-1993 | 1993-04-01(R 1998) | English | Test Slabs, Fluoroelastomer (FKM) 65 - 75 DoD Adopted |
486 | SAE AMS3217A-1993 | 1993-04-01(R 1998) | English | Standard Elastomer Stocks Test Slabs DoD Adopted | ANSI Approved |
487 | SAE AMS5549G-1993 | 1993-04-01 | English | Steel, Corrosion and Heat Resistant, Plate 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated - UNS S35500 |
488 | SAE J590-1993 | 1993-04-01 | English | Turn Signal Flashers ANSI Approved |
489 | SAE AS7235-1993 | 1993-04-01 | English | Rivets, UNS S66286, Steel, Corrosion and Heat Resistant, 80 ksi Shear Strength, Procurement Specification for |
490 | SAE J2056/2-1993 | 1993-04-01 | English | Survey of Known Protocols, Information Report |
491 | SAE AIR4498A-1993 | 1993-04-01 | English | Aus-Bay Quenching of 300M Steel - This document has been declared "Stabilized" by SAE |
492 | SAE AMS3217A-1993 | 1993-04-01 | English | Standard Elastomer Stocks Test Slabs |
493 | SAE AIR4498-1993 | 1993-04-01 | English | Aus-Bay Quenching of 300M Steel ANSI Approved |
494 | SAE AMS4789A-1993 | 1993-04-01 | English | SILVER ALLOY BRAZING FILLER METAL 56AG - 22CU - 17ZN - 5.0SN 1152 TO 1205 DEGREES F (618 TO 652 DEGREES C) SOLIDUS-LIQUIDUS RANGE |
495 | SAE MA4360-1993 | 1993-03-31(R 2004) | English | Metric Wrenches: Nondistorting Flare Nut DoD Adopted |
496 | SAE AS4167A-1993 | 1993-03-31(R 2004) | English | Wrenches; Flare Nut, Crowfoot, 12-Point Nondistorting DoD Adopted |
497 | SAE AS4011-1993 | 1993-03-29(R 2007) | English | HOSE ASSEMBLY, POLYETRAFLUOROETHYLENE, PTFE, METAL BRAID, MEDIUM PRESSURE, BEAM SEAL, 90掳 TO 90掳 |
498 | SAE AS7473A-1993 | 1993-03-18(R 2004) | English | Bolts and Screws Roll Threaded Procurement Specification for - UNS K00802,UNS K91505,UNS K91456,UNS S32100,UNS S34700 DoD Adopted |
499 | SAE ARP588B-1993 | 1993-03-16 | English | Balancing Machines - Description and Evaluation Vertical, Single-Plane, Soft-Bearing Type for Gas Turbine Rotors ANSI Approved |
500 | SAE AIR1973A-1993 | 1993-03-01(R 2013) | English | Trademarks, Hydraulic System Component Manufacturers, Index of |
|