| Pos | standard Number | publication date | Language | Description |
| 1 | SAE AS8016A-1996 | 1996-01-01 | English | Vertical Velocity Instrument (Rate-of- Climb) |
| 2 | SAE ARP920A-1996 | 1996-01-01 | English | Design and Installation of Pitot-Static Systems for Transport Aircraft |
| 3 | SAE ARP921A-1996 | 1996-01-01 | English | Flight Test Procedures for Static Pressure Systems Installed in Subsonic Transport Aircraft |
| 4 | SAE AS8019A-1996 | 1996-01-01 | English | Airspeed Instruments |
| 5 | SAE HS-3200-1996 | 1996-01-01 | English | Passenger Car Safety Standards Manual - ***To Purchase: Contact IHS at 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide*** |
| 6 | SAE J1701M-1996 | 1996-01-01 | English | Torque-Tension Tightening for Metric Series Fasteners, Information Report |
| 7 | SAE J266-1996 | 1996-01-01 | English | Steady-State Directional Control Test Procedures for Passenger Cars and Light Trucks |
| 8 | SAE J2298-1996 | 1996-01-01 | English | Ultraviolet Leak Detection: Procedure for Use of Refrigerant Leak Detection Dyes for Service of Mobile Air-Conditioning Systems, Standard |
| 9 | SAE ARD9000-1996 | 1996-01-01 | English | Aerospace Basic Quality System Standard |
| 10 | SAE HS-1417-1996 | 1996-01-01 | English | SAE Fluid Sealing Handbook Radial Lip Seals |
| 11 | SAE J2299-1996 | 1996-01-01 | English | Ultraviolet Leak Detection: Performance Requirements for Fluorescent Refrigerant Leak Detection Dye Injection Equipment for Aftermarket Service of Mobile Air- Conditioning Systems, Standard |
| 12 | SAE HS-3458-1996 | 1996-01-01 | English | Fuel Injection Systems and Testing Methods Standards Manual - ***To Purchase: Contact IHS at 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide*** |
| 13 | SAE AS8005A-1996 | 1996-01-01 | English | Minimum Performance Standard Temperature Instruments |
| 14 | SAE J2280-1996 | 1996-01-01 | English | Ship Systems and Equipment - Fasteners - Selection and Identification Requirements, Standard |
| 15 | SAE ARP465B-1996 | 1996-01-01 | English | Flange - Thermocouple |
| 16 | SAE J1053-1996 | 1996-01-01 | English | (R) Steel Stamped Nuts of One Pitch Thread Design - Inch Series, Standard
DoD Adopted |
| 17 | SAE J1673-1996 | 1996-01-01 | English | High Voltage Automotive Wiring Assembly Design, Recommended Practice |
| 18 | SAE ARP485A-1996 | 1996-01-01 | English | Temperature Measuring Devices Nomenclature |
| 19 | SAE AS8002A-1996 | 1996-01-01 | English | Air Data Computer - Minimum Performance Standard |
| 20 | SAE J744-1996 | 1996-01-01 | English | Hydraulic Pump and Motor Mounting and Drive Dimensions, Standard
DoD Adopted |
| 21 | SAE J1667-1996 | 1996-01-01 | English | Snap-Acceleration Smoke Test Procedure for Heavy-Duty Diesel Powered Vehicles, Recommended Practice |
| 22 | SAE MA3330C-1995 | 1995-12-01(R 2012) | English | INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, SCREW LOCKING, CRES, DRY FILM LUBRICATED |
| 23 | SAE MA3329C-1995 | 1995-12-01(R 2012) | English | INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, SCREW LOCKING, CRES, UNCOATED |
| 24 | SAE MA3331C-1995 | 1995-12-01(R 2012) | English | INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, SCREW LOCKING, CRES, CADMIUM PLATED |
| 25 | SAE MA3279B-1995 | 1995-12-01(R 2012) | English | Insert, Screw Thread, Helical Coil, Metric Series, Free Running, CRES, Uncoated |
| 26 | SAE MA3280B-1995 | 1995-12-01(R 2012) | English | INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, FREE RUNNING, CRES, DRY FILM LUBRICATED |
| 27 | SAE ARP4943-1995 | 1995-12-01(R 2008) | English | Ground Support Equipment Hydraulic Systems, Design and Installation, Recommended Practices For |
| 28 | SAE AS2094-1995 | 1995-12-01(R 2007) | English | Test Methods for Tube-Fitting Assemblies |
| 29 | SAE AS5019-1995 | 1995-12-01(R 2007) | English | NUT, BULKHEAD, BEAM SEAL FITTING |
| 30 | SAE ARP89D-1995 | 1995-12-01(R 2007) | English | Aircraft Compartment Automatic Temperature Control Systems |
| 31 | SAE MA2094-1995 | 1995-12-01(R 2007) | English | Test Methods for Tube-Fitting Assemblies, Metric (ISO 10583) |
| 32 | SAE ARP1962A-1995 | 1995-12-01(R 2007) | English | Training and Approval of Heat-Treating Personnel |
| 33 | SAE AS4825-1995 | 1995-12-01(R 2007) | English | Gasket, Fitting End, 24 Degree Cone |
| 34 | SAE MA2005B-1995 | 1995-12-01(R 2007) | English | Tube Fittings, Aerospace Fluid Systems, Separable, For 24掳 Cone, General Specification, Metric (ISO 7169) |
| 35 | SAE MA3330C-1995 | 1995-12-01(R 2006) | English | Insert, Screw Thread, Helical Coil, Metric Series, Screw Locking, CRES, Dry Film Lubricated
DoD Adopted |
| 36 | SAE MA3281B-1995 | 1995-12-01(R 2006) | English | INSERT, SCREW THREAD, HELICAL COIL, METRIC SERIES, FREE RUNNING, CRES, CADMIUM PLATED |
| 37 | SAE MA3280B-1995 | 1995-12-01(R 2006) | English | Insert, Screw Thread, Helical Coil, Metric Series, Free Running, CRES, Dry Film Lubricated |
| 38 | SAE MA3279B-1995 | 1995-12-01(R 2006) | English | Insert, Screw Thread, Helical Coil, Metric Series, Free Running, CRES, Uncoated
DoD Adopted |
| 39 | SAE MA3331C-1995 | 1995-12-01(R 2006) | English | Insert, Screw Thread, Helical Coil, Metric Series, Screw Locking, CRES, Cadmium Plated |
| 40 | SAE MA3329C-1995 | 1995-12-01(R 2006) | English | Insert, Screw Thread, Helical Coil, Metric Series, Screw Locking, CRES, Uncoated
DoD Adopted |
| 41 | SAE AS7474B-1995 | 1995-12-01(R 2006) | English | Bolts and Screws, Steel, Corrosion Resistant, UNS S17400 Tensile Strength 140 ksi Procurement Specification
DoD Adopted |
| 42 | SAE AS4786-1995 | 1995-12-01(R 2004) | English | Driver Drills Battery Powered |
| 43 | SAE AS5018-1995 | 1995-12-01 | English | Washer, Flat, Beam Seal Fitting |
| 44 | SAE AS4825-1995 | 1995-12-01 | English | Gasket, Fitting End, 24 Degree Cone |
| 45 | SAE ARP89D-1995 | 1995-12-01 | English | Aircraft Compartment Automatic Temperature Control Systems |
| 46 | SAE MA2094-1995 | 1995-12-01 | English | Test Methods for Tube-Fitting Assemblies, Metric |
| 47 | SAE AS5019-1995 | 1995-12-01 | English | NUT, BULKHEAD, BEAM SEAL FITTING |
| 48 | SAE MA2005B-1995 | 1995-12-01 | English | Tube Fittings, Aerospace Fluid Systems, Separable, For 24° Cone, General Specification, Metric |
| 49 | SAE ARP4005A-1995 | 1995-12-01 | English | Selection and Application of Relays for Proper Performance
DoD Adopted | ANSI Approved |
| 50 | SAE J1751-1995 | 1995-12-01 | English | Lubrication Components and Systems Used on Machine Tools and Equipment for the Automotive Industry, Recommended Practice |
| 51 | SAE AIR4896-1995 | 1995-12-01 | English | Recommended RMS Terms and Parameters |
| 52 | SAE J2205-1995 | 1995-12-01 | English | Expanded Diagnostic Protocol for OBD II Scan Tools, Recommended Practice |
| 53 | SAE ARP89D-1995 | 1995-12-01 | English | Aircraft Compartment Automatic Temperature Control Systems |
| 54 | SAE AS1099C-1995 | 1995-11-01(R 2014) | English | FITTING END, BULKHEAD FLARED TUBE, FOR SEAL RING, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
| 55 | SAE AS1098B-1995 | 1995-11-01(R 2014) | English | FITTING END, FLARED TUBE, FOR SEAL RING, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
| 56 | SAE ARP1611A-1995 | 1995-11-01(R 2014) | English | Quality Inspection Procedure, Composites Tracer Fluoroscopy and Radiography |
| 57 | SAE AS3570-1995 | 1995-11-01(R 2012) | English | PACKING, PREFORMED – O-RING SEAL AMS7274 |
| 58 | SAE AS3569-1995 | 1995-11-01(R 2012) | English | PACKING, PREFORMED – O-RING SEAL AMS7270 |
| 59 | SAE AS15531-1995 | 1995-11-01(R 2011) | English | Digital Time Division Command/Response Multiplex Data Bus |
| 60 | SAE AIR844B-1995 | 1995-11-01(R 2008)(S 2014) | English | Sensitization and Corrosion in Stainless Steel Filters |
| 61 | SAE AIR844A-1995 | 1995-11-01(R 2008) | English | Sensitization and Corrosion in Stainless Steel Filters |
| 62 | SAE AS1099C-1995 | 1995-11-01(R 2007) | English | FITTING END, BULKHEAD FLARED TUBE, FOR SEAL RING, STANDARD DIMENSIONS FOR, DESIGN STANDARD |
| 63 | SAE AS1098B-1995 | 1995-11-01(R 2007) | English | Fitting End, Flared Tube, for Seal Ring, Standard Dimensions for, Design Standard |
| 64 | SAE AMS5363E-1995 | 1995-11-01(R 2007) | English | Steel Castings, Sand and Centrifugal, Corrosion and Heat Resistant 18.5Cr - 10.5Ni - 0.90 (Cb+Ta) Solution Heat Treated - UNS J92641; Reaffirmed Noncurrent January 2002
DoD Adopted |
| 65 | SAE AS15531-1995 | 1995-11-01(R 2006) | English | Digital Time Division Command/Response Multiplex Data Bus |
| 66 | SAE MA3375B-1995 | 1995-11-01(R 2006) | English | Studs, Corrosion and Heat Resistant Steel, UNS S66286 Tensile Strength 900 MPa, Procurement Specification, Metric |
| 67 | SAE AS3570-1995 | 1995-11-01(R 2006) | English | Packing, Preformed - O-Ring Seal AMS 7274
DoD Adopted |
| 68 | SAE AS3569-1995 | 1995-11-01(R 2006) | English | Packing, Preformed - O-Ring Seal AMS 7270
DoD Adopted |
| 69 | SAE AIR1364A-1995 | 1995-11-01(R 2003) | English | Age Control of Age Sensitive Elastomeric Materials |
| 70 | SAE J1984-1995 | 1995-11-01(R 2002) | English | Diesel Fuel Injector Assembly Type 28 (9.5 mm) |
| 71 | SAE J1633-1995 | 1995-11-01(R 2000) | English | Laboratory Speed Test Procedure for Light Truck Tires |
| 72 | SAE J1633-1995 | 1995-11-01 | English | Laboratory Speed Test Procedure for Light Truck Tires |
| 73 | SAE AMS6441H-1995 | 1995-11-01 | English | Steel Tubing, Mechanical 1.45Cr (0.98 - 1.10C) (SAE 50100) For Bearing Applications |
| 74 | SAE J543-1995 | 1995-11-01 | English | (R) Starting Motor Pinions and Ring Gears |
| 75 | SAE AMS4230D-1995 | 1995-11-01 | English | ALUMINUM ALLOY CASTINGS, SAND 4.5CU(195-T4) SOLUTION |
| 76 | SAE AMS4220E-1995 | 1995-11-01 | English | ALUMINUM ALLOY CASTINGS, SAND 4CU-2NI-1.5MG |
| 77 | SAE ARP1611A-1995 | 1995-11-01 | English | Quality Inspection Procedure, Composites Tracer Fluoroscopy and Radiography |
| 78 | SAE AMS3909/1A-1995 | 1995-10-01(R 2014) | English | (R) Cloth, Aramid 3.0 Ounces per Square yard (102 g/m2), 350 Pounds Force per Inch (61 294 N/m) |
| 79 | SAE AMS3909/2A-1995 | 1995-10-01(R 2014) | English | (R) Cloth, Aramid 2.25 Ounces per Square Yard (76.3 g/m2), 250 Pounds Force per Inch (43 782 N/m) |
| 80 | SAE AMS3909/3A-1995 | 1995-10-01(R 2014) | English | (R) Cloth, Aramid 2.0 Ounces per Square Yard (68 g/m2), 230 Pounds Force per Inch (40 279 N/m) (Warp) and 220 Pounds Force per Inch (38 528 N/m) (Filling) |
| 81 | SAE AS4098A-1995 | 1995-10-01(R 2013) | English | Hose Assembly, Polytetrafluoroethylene, Heavy Duty, Metallic Reinforced, 400 °F, 5000 psi Hydraulic and Pneumatic |
| 82 | SAE J397-1995 | 1995-10-01(R 2009) | English | Deflection Limiting Volume鈥擯rotective Structures Laboratory Evaluation |
| 83 | SAE AS4098A-1995 | 1995-10-01(R 2007) | English | Hose Assembly, Polytetrafluoroethylene, Heavy Duty, Metallic Reinforced, 400 Degrees F, 5000 psi Hydraulic and Pneumatic |
| 84 | SAE MA4098-1995 | 1995-10-01(R 2007) | English | Hose Assembly, Polytetrafluoroethylene, Heavy Duty, Metallic Reinforced, 204 掳C, 35 000 kPa Hydraulic and Pneumatic, Metric |
| 85 | SAE AMS5546D-1995 | 1995-10-01(R 2007) | English | Steel Sheet and Strip, Corrosion and Moderate Heat Resistant 16.5Cr - 4.5Ni - 2.9Mo - 0.10N Cold Rolled, Temperedq |
| 86 | SAE AS3565-1995 | 1995-10-01(R 2006) | English | Washer, Flat, Countersunk UNS S66286 |
| 87 | SAE AS4726-1995 | 1995-10-01(R 2006) | English | Nuts, Self-Locking, UNS S66286 Classification: 220 ksi/850 Degrees F Procurement Specification |
| 88 | SAE MA3374A-1995 | 1995-10-01(R 2006) | English | Bolts and Screws, UNS S66286, Corrosion and Heat Resistant Steel, Procurement Specification, Metric - UNS S66286
DoD Adopted |
| 89 | SAE AIR4176-1995 | 1995-10-01(R 2005) | English | Cost Versus Benefits of Engine Monitoring Systems |
| 90 | SAE AMS3373B-1995 | 1995-10-01(R 2001) | English | Compound, Silicone Rubber, Insulating and Sealing 35 to 55 |
| 91 | SAE AMS3909/2A-1995 | 1995-10-01(R 2001) | English | (R) Cloth, Aramid 2.25 Ounces per Square Yard (76.3 g/m2), 250 Pounds Force per Inch (43,782 N/m) |
| 92 | SAE AMS3909/1A-1995 | 1995-10-01(R 2001) | English | (R) Cloth, Aramid 3.0 Ounces per Square Yard (102 g/m2), 350 Pounds Force per Inch (61,294 N/m) |
| 93 | SAE AMS3909/3A-1995 | 1995-10-01(R 2001) | English | (R) Cloth, Aramid 2.0 Ounces per Square Yard (68 g/m2), 230 Pounds Force per Inch (40,279 N/m) (Warp) and 220 Pounds Force per Inch (38,528 N/m) (Filling) |
| 94 | SAE J1460-1-1995 | 1995-10-01(R 2000) | English | Human Mechanical Impact Response Characteristics - Dynamic Response of the Human Abdomen
ANSI Approved |
| 95 | SAE AMS3853B-1995 | 1995-10-01 | English | CORD, AROMATIC POLYAMIDE, NONMELTING |
| 96 | SAE AMS3858E-1995 | 1995-10-01 | English | Asbestos Felting, "B" Stage Phenolic Resin Impregnated Low Pressure Molding |
| 97 | SAE ARP4874-1995 | 1995-10-01 | English | Electronic Propulsion Control/Aircraft Interface Control Documents |
| 98 | SAE AMS3510B-1995 | 1995-10-01 | English | COATING, ABRASION RESISTANT FOR POLYCARBONATE PARTS |
| 99 | SAE AMS3532C-1995 | 1995-10-01 | English | ETHYLENE TETRAFLUOROETHYLENE (ETFE) MOLDED SHEET STRESS-RELIEVED |
| 100 | SAE AMS3533C-1995 | 1995-10-01 | English | ETHYLENE TETRAFLUOROETHYLENE (ETFE) EXTRUSIONS |
| 101 | SAE AMS3534C-1995 | 1995-10-01 | English | ETHYLENE TETRAFLUOROETHYLENE (ETFE) MOLDINGS STRESS-RELIEVED |
| 102 | SAE AMS3569C-1995 | 1995-10-01 | English | FOAM, FLEXIBLE POLYURETHANE (PUR) OPEN PORE, POLYVINYLCHLORIDE (PVC) COATED |
| 103 | SAE AMS3580D-1995 | 1995-10-01 | English | CAST RODS, TUBES, AND SHAPES METHYL METHACRYLATE PLASTIC |
| 104 | SAE AMS3581C-1995 | 1995-10-01 | English | CAST RODS, TUBES, AND SHAPES, METHYL METHACRYLATE PLASTIC HEAT RESISTANT |
| 105 | SAE AMS3672C-1995 | 1995-10-01 | English | PLASTIC MOLDINGS AND EXTRUSIONS, METHYL METHACRYLATED HEAT - RESISTANT |
| 106 | SAE AMS3682E-1995 | 1995-10-01 | English | COATING MATERIAL, ELECTRICALLY CONDUCTIVE SILVER - ORGANIC RESIN |
| 107 | SAE AMS3777/1B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 3/4 (19) WIDE, 400 (1780 N) BREAKING STRENGTH |
| 108 | SAE AMS3777/2B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 9/16 (14) WIDE, 500 (2225 N) BREAKING STRENGTH |
| 109 | SAE AMS3777/3B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 1 (25) WIDE, 1000 (4450 N) BREAKING STRENGTH |
| 110 | SAE AMS3777/4B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 1-1/2 (38) WIDE, 1500 (6670 N) BREAKING STRENGTH |
| 111 | SAE AMS3777/5B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 1 (25) WIDE, (2335 N) BREAKING STRENGTH |
| 112 | SAE AMS3777/6B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 5/16 (8) WIDE 350 (1555 N) BRAKING STRENGTH |
| 113 | SAE AMS3777/7B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 2 (50) WIDE, 1500 (6670 N) BREAKING STRENGTH |
| 114 | SAE AMS3785A-1995 | 1995-10-01 | English | CLOTH, META-ARAMID WARP META-ARAMID/PARA-ARAMID OR |
| 115 | SAE AMS3784B-1995 | 1995-10-01 | English | TAPE, NYLON, LOOP |
| 116 | SAE AMS3777/8B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 2 (50) WIDE, 2000 (8895 N) BREAKING STRENGTH |
| 117 | SAE AMS3777/9B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING 2 (50) WIDE, 3000 913,345 N) BREAKING STRENGTH |
| 118 | SAE AMS3783B-1995 | 1995-10-01 | English | GLASS CLOTH, CHLOROPRENE (CR) COATED |
| 119 | SAE AMS3777B-1995 | 1995-10-01 | English | TAPE, NYLON, NONMELTING, REINFORCING |
| 120 | SAE AMS3853/3B-1995 | 1995-10-01 | English | CORD, AROMATIC POLYAMIDE, NONMELTING 550 POUNDS (2445 N), 165 FOOT/POUNDS (110 M/KG) |
| 121 | SAE AMS3853/2B-1995 | 1995-10-01 | English | CORD, AROMATIC POLYAMIDE, NONMELTING 375 POUNDS (1670 N), 230 FOOT/POUNDS (155 M/KG) |
| 122 | SAE AMS3853/1B-1995 | 1995-10-01 | English | CORD, AROMATIC POLYAMIDE, NONMELTING 100 POUNDS (445 N), 780 FOOT/POUNDS (525 M/KG) |
| 123 | SAE AMS3850B-1995 | 1995-10-01 | English | CLOTH, CHLOROPHRENE (CR) COATED NYLON |
| 124 | SAE AMS3848B-1995 | 1995-10-01 | English | CLOTH, NYLON, METALLIZED |
| 125 | SAE AMS3848/2B-1995 | 1995-10-01 | English | CLOTH, NYLON, METALLIZED WATER REPELLENT TREATED |
| 126 | SAE AMS3848/1B-1995 | 1995-10-01 | English | CLOTH, NYLON, METALLIZED UNTREATED |
| 127 | SAE AMS3139A-1995 | 1995-10-01 | English | ADHESIVE, URETHANE TWO-PART |
| 128 | SAE AMS3727B-1995 | 1995-10-01 | English | RESIN, EPOXY, MATRIX, THERMOSETTING MODERATE TEMPERATURE RESISTANT, UNFILLED |
| 129 | SAE AMS2443A-1995 | 1995-10-01 | English | EPOXY PRIMER PLATING ELECTRODEPOSITION |
| 130 | SAE AMS2467-1995 | 1995-10-01 | English | Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage |
| 131 | SAE AMS3871C-1995 | 1995-10-01 | English | GLAZED CERAMIC SHEET 95% ALUMINA |
| 132 | SAE AMS3883A-1995 | 1995-10-01 | English | Glass Sheet, Barium Aluminum Borosilicate for Electronic Applications |
| 133 | SAE ARP1643B-1995 | 1995-10-01 | English | FABRICATION OF GRAPHITE FIBER/POLYSULFONE RESIN COMPOSITE STRUCTURES |
| 134 | SAE AMS3641E-1995 | 1995-10-01 | English | PLASTIC MOLDINGS, THERMOSETTING PHENOL/FORMALDEHYDE, MACERATED - FABRIC-FILLED |
| 135 | SAE AMS3790/1B-1995 | 1995-10-01 | English | CLOTH, MONOFILAMENT, NETTING 12 X 12 MESH, 13 OUNCES/SQUARE YARD |
| 136 | SAE AMS3691C-1995 | 1995-10-01 | English | ADHESIVE COMPOUND, EPOXY MEDIUM TEMPERATURE APPLICATION |
| 137 | SAE AMS3624D-1995 | 1995-10-01 | English | PLASTIC MOLDINGS AND EXTRUSIONS, CELLULOSE ACETATE BUTYRATE |
| 138 | SAE AMS3788/4B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 5.5 OUNCES PER SQUARE YARD 9186 G/M2) SMOOTH FINISH, WATER REPELLENT TREATED |
| 139 | SAE AMS3788/1B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 3.3 OZ PER SQUARE YARD (112G/M2), SMOOTH FINISH |
| 140 | SAE AMS3627D-1995 | 1995-10-01 | English | PLASTIC MOLDINGS AND EXTRUSIONS, METHYL METHACRYLATE HEAT - RESISTANT |
| 141 | SAE AMS3296B-1995 | 1995-10-01 | English | DIGLYCIDYL ESTER RESIN |
| 142 | SAE AMS3790B-1995 | 1995-10-01 | English | CLOTH, MONOFILAMENT, NETTING |
| 143 | SAE AMS3790/2B-1995 | 1995-10-01 | English | CLOTH, MONOFILAMENT, NETTING 20 X 20 MESH, 7 OUNCES/SQUARE YARD |
| 144 | SAE AMS3703B-1995 | 1995-10-01 | English | ADHESIVE, ELECTRICALLY NON-CONDUCTIVE MODERATELY RAPID CURE |
| 145 | SAE AMS3788B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL |
| 146 | SAE AMS3788/6B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 5.4 OZ PER SQUARE YARD (183 G/M2) SMOOTH FINISH, HEAVILY CALENDERED, WATER REPELLENT TREATED |
| 147 | SAE AMS3702B-1995 | 1995-10-01 | English | EPOXY RESIN, TETRAGLYCIDYL METHYLENEDIANILINE 14, 000 TO 18,000 CENTIPOISE VISCOSITY |
| 148 | SAE AMS3591C-1995 | 1995-10-01 | English | POLYETHYLENE TEREPHTHALATE PLASTIC TUBING, ELECTRICAL INSULATION - THERMALLY WELDED, HEAT SHRINKABLE 1.6 TO 1 SHRINK RATIO |
| 149 | SAE AMS3788/2B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 3.3 OUNCES PER SQUARE YARD (112 G/M2) SMOOTH FINISH, WATER REPELLENT TREATED |
| 150 | SAE AMS3788/3B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 5.4 OUNCES SQUARE YARD (183 G/M2), SMOOTH FINISH |
| 151 | SAE AMS3598E-1995 | 1995-10-01 | English | Plastic Sheet, Copper Faced, GTN Glass Fabric Reinforced Polytetrafluoroethylene
DoD Adopted |
| 152 | SAE AMS2467-1995 | 1995-10-01 | English | Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage |
| 153 | SAE AMS3820A-1995 | 1995-10-01 | English | Tape, Nylon Cloth for Ring-Slot Parachutes |
| 154 | SAE AMS3099B-1995 | 1995-10-01 | English | CURING AGING, SOLID AROMATIC AMINE, 4,4' - DIAMONODIPHENYL SULFONE |
| 155 | SAE AMS3701C-1995 | 1995-10-01 | English | EPOXY RESIN, TETRAGLYCIDYL METHYLENEDIANILINE (TGMDA) 10,000 TO 14,000 CENTIPOISE VISCOSITY |
| 156 | SAE AMS3087H-1995 | 1995-10-01 | English | COMPOUND, INSULATING AND SEALING SILICONE |
| 157 | SAE AMS3137D-1995 | 1995-10-01 | English | RESIN, CONFORMAL COATING, URETHANE ELASTOMER |
| 158 | SAE AMS3788/5B-1995 | 1995-10-01 | English | CLOTH, NYLON TWILL 5.4 OUNCES PER SQUARE YARD (183 G/M2) SMOOTH FINISH, HEAVILY CALENDERED |
| 159 | SAE AMS3706B-1995 | 1995-10-01 | English | EPOXY RESIN, POLYFUNCTIONAL SOLID |
| 160 | SAE AMS3583D-1995 | 1995-10-01 | English | PLASTIC TUBING, ELECTRICAL INSULATION CROSSLINDED POLYVINYL CHLORIDE, SEMI-RIGID HEAT SHRINKABLE 2 TO 1 SHRINK RATIO |
| 161 | SAE AMS3590E-1995 | 1995-10-01 | English | PLASTIC SHEET, COPPER FACED PAPER REINFORCED PHENOLIC RESIN |
| 162 | SAE AMS3708B-1995 | 1995-10-01 | English | ADHESIVE, EPOXY PASTE, FOR STRUCTURAL WELDBOND FOR 80 DEGREES C (180 DEGREES F) SERVICE |
| 163 | SAE AMS3789B-1995 | 1995-10-01 | English | CLOTH, TWILL NYLON WARP, RAYON FILLING |
| 164 | SAE AMS3824C-1995 | 1995-09-01(R 2013) | English | Cloth, Glass Finished for Resin Laminates |
| 165 | SAE AS4060-1995 | 1995-09-01(R 2013) | English | Tube Fitting Swaged Joint, Roller Expander Manual Process, Requirements for |
| 166 | SAE MA4039A-1995 | 1995-09-01(R 2012) | English | Washer, Key - 270 Degree Locking, Cres, UNS S32100, Metric |
| 167 | SAE MA4040A-1995 | 1995-09-01(R 2012) | English | WASHER, KEY - DUAL LOCKING POSITIONS, CRES, UNS S32100, METRIC |
| 168 | SAE MA4037A-1995 | 1995-09-01(R 2012) | English | WASHER, KEY - 90° LOCKING, CRES, UNS S32100, METRIC |
| 169 | SAE AS1773-1995 | 1995-09-01(R 2008) | English | Fiber Optics Mechanization of a Digital Time Division Command/Response Multiplex Data Bus |
| 170 | SAE J1354-1995 | 1995-09-01(R 2007) | English | Nomenclature - Forwarder |
| 171 | SAE AS4060-1995 | 1995-09-01(R 2007) | English | Tube Fitting Swaged Joint, Roller Expander Manual Process, Requirements for |
| 172 | SAE J1254-1995 | 1995-09-01(R 2007) | English | Component Nomenclature - Feller Buncher |
| 173 | SAE MA4039A-1995 | 1995-09-01(R 2006) | English | Washer, Key - 270 Degree Locking, Cres, UNS S32100, Metric - UNS S32100
DoD Adopted |
| 174 | SAE MA4040A-1995 | 1995-09-01(R 2006) | English | Washer, Key - Dual Locking Positions, Cres, UNS S32100, Metric - UNS S32100
DoD Adopted |
| 175 | SAE MA4037A-1995 | 1995-09-01(R 2006) | English | Washer, Key - 90 Degree Locking, Cres, UNS S32100, Metric - UNS S32100
DoD Adopted |
| 176 | SAE AMS3824C-1995 | 1995-09-01(R 2003) | English | Cloth, Glass Finished for Resin Laminates
DoD Adopted |
| 177 | SAE AMS3383-1995 | 1995-09-01(R 2001) | English | Polytetrafluoroethylene (PTFE) - Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 75 - 85 |
| 178 | SAE R-154-1995 | 1995-09-01 | English | Allied Aircraft Piston Engines of World War II - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 179 | SAE AMS5813C-1995 | 1995-09-01 | English | STEEL WELDING WIRE, CORROS & MOD HEAT RESIS, 14.5CR |
| 180 | SAE AIR1490B-1995 | 1995-08-01(R 2013) | English | Environmental Degradation of Textiles |
| 181 | SAE ARP4848-1995 | 1995-08-01(R 2012) | English | Flaring (Swaging) and Removal of Shank Nuts |
| 182 | SAE ARP4033-1995 | 1995-08-01(R 2008) | English | Pilot-System Integration |
| 183 | SAE AS4041A-1995 | 1995-08-01(R 2008) | English | AIR MODE GENERAL PURPOSE CONTAINERS |
| 184 | SAE AMS3217/7-1995 | 1995-08-01(R 2007) | English | TEST SLABS, HIGH STRENGTH, FLUOROSILICONE (FVMQ) 55 - 65 |
| 185 | SAE AIR4653-1995 | 1995-08-01(R 2007) | English | Flight Management Systems Review |
| 186 | SAE AIR1490B-1995 | 1995-08-01(R 2007) | English | Environmental Degradation of Textiles |
| 187 | SAE J764-1995 | 1995-08-01(R 2006) | English | Loading Ability Test ProcedureScrapers |
| 188 | SAE J1536-1995 | 1995-08-01(R 2006) | English | Two-Stroke-Cycle Engine Oil Fluidity/Miscibility Classification |
| 189 | SAE AMS3681C-1995 | 1995-08-01(R 2005) | English | Adhesive, Electrically Conductive Silver-Filled Epoxy Resin |
| 190 | SAE ARP4848-1995 | 1995-08-01(R 2004) | English | Flaring (Swaging) and Removal of Shank Nuts
DoD Adopted |
| 191 | SAE AIR1855A-1995 | 1995-08-01(R 2004) | English | Actuation System Data Summary for Missiles and Launch Vehicles |
| 192 | SAE MA4535-1995 | 1995-08-01(R 2004) | English | Wrenches, Box and Open End Combination Twelve Point, High Strength, Thin Wall, Metric |
| 193 | SAE J1510-1995 | 1995-08-01(R 2001) | English | Lubricants for Two-Stroke-Cycle Gasoline Engines |
| 194 | SAE AIR1855A-1995 | 1995-08-01 | English | Actuation System Data Summary for Missiles and Launch Vehicles |
| 195 | SAE J1663-1995 | 1995-08-01 | English | Truth-in-Labeling Standard for Navigation Map Databases, Standard |
| 196 | SAE AIR4653-1995 | 1995-08-01 | English | Flight Management Systems Review |
| 197 | SAE J1627-1995 | 1995-08-01 | English | (R) Performance Criteria for Electronic Refrigerant Leak Detectors, Standard |
| 198 | SAE J1524-1995 | 1995-08-01 | English | (R) Method of Viscosity Test for Automotive Type Adhesives, Sealers, and Deadeners, Recommended Practice |
| 199 | SAE AIR1855A-1995 | 1995-08-01 | English | Actuation System Data Summary for Missiles and Launch Vehicles |
| 200 | SAE AMS3500F-1995 | 1995-08-01 | English | Leather, Chrome-Vegetable Retained, Cattle Hide Fuel and Hot Oil Resistant |
| 201 | SAE J1723-1995 | 1995-08-01 | English | Supercharger Testing Standard, Standard |
| 202 | SAE AMS4264A-1995 | 1995-08-01 | English | BRONZE, ALUMINUM SILICON RODS, BARS, AND FORGINGS 90CU - 7.0A1 - 1.8SI DRAWN AND STRESS RELIEVED (HR50) |
| 203 | SAE ARP1511B-1995 | 1995-08-01 | English | Corrosion of Low-Embrittling Cadmium Plate by Aircraft Maintenance Chemicals |
| 204 | SAE AMS5809A-1995 | 1995-08-01 | English | ALLOY WELDING WIRE, CORROSION AND HEAT RESISTANT 52C0 - 20CR - 20N1 - 7.5TA VACUUM MELTED |
| 205 | SAE ARP1512B-1995 | 1995-08-01 | English | Corrosion of Aluminum Alloys by Aircraft Maintenance Chemicals Sandwich Test
DoD Adopted |
| 206 | SAE ARP4698-1995 | 1995-07-01(R 2013) | English | Guide for Choosing a Minimum Wall Thickness of Tubing for Use With Weld Fittings Coded for a Range of Wall Sizes |
| 207 | SAE AMS2664F-1995 | 1995-07-01(R 2009) | English | BRAZING, SILVER For Use Up to 800 DEGREES F (427 DEGREES C) |
| 208 | SAE AMS2664F-1995 | 1995-07-01(R 2009) | English | BRAZING, SILVER For Use Up to 800 DEGREES F (427 DEGREES C) |
| 209 | SAE AS4863-1995 | 1995-07-01(R 2007) | English | Plug, Pipe, External Thread
DoD Adopted |
| 210 | SAE AIR1245A-1995 | 1995-07-01(R 2007) | English | (R) Power Sources for Fluidic Controls |
| 211 | SAE ARP4698-1995 | 1995-07-01(R 2007) | English | Guide for Choosing a Minimum Wall Thickness of Tubing for Use With Weld Fittings Coded for a Range of Wall Sizes |
| 212 | SAE AS4157A-1995 | 1995-07-01(R 2004) | English | Coupling Assemblies, Hydraulic, Self-Sealing, Quick Disconnect 5000 and 8000 Pounds per Square Inch, Gage |
| 213 | SAE J347-1995 | 1995-07-01(R 2002) | English | Diesel Fuel Injector Assembly Type 7 (9.5 mm) |
| 214 | SAE J1113-41-1995 | 1995-07-01(R 2000) | English | Limits and Methods of Measurement of Radio Disturbance Characteristics of Components and Modules for the Protection of Receivers Used on Board Vehicles |
| 215 | SAE J447-1995 | 1995-07-01 | English | (R) Prevention of Corrosion of Motor Vehicle Body and Chassis Components |
| 216 | SAE R-155-1995 | 1995-07-01 | English | An Engineer in the Courtroom - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 217 | SAE J1086-1995 | 1995-07-01 | English | Numbering Metals and Alloys, Recommended Practice
DoD Adopted |
| 218 | SAE J1559-1995 | 1995-07-01 | English | Measurement of Solar Heating Effect
DoD Adopted |
| 219 | SAE AMS2664F-1995 | 1995-07-01 | English | Brazing, Silver For Use Up to 800 °F (427 °C) |
| 220 | SAE AMS3826B-1995 | 1995-07-01 | English | (R) Cloth, Type "E" Glass "B" Stage Polyester Resin Impregnated 1581 and 7781 Type Fabric |
| 221 | SAE AS107D-1995 | 1995-07-01 | English | Surface Finish (RMS) - Reaffirmed Noncurrent May 2006 |
| 222 | SAE AS4863-1995 | 1995-07-01 | English | Plug, Pipe, External Thread |
| 223 | SAE J415-1995 | 1995-07-01 | English | (R) Definition of Heat Treating Terms |
| 224 | SAE AS4983-1995 | 1995-06-01(R 2012) | English | Spring Pins, Tubular, Coiled Corrosion Resistant Nickel Base Alloy Procurement Specification For |
| 225 | SAE AS3577-1995 | 1995-06-01(R 2012) | English | PIN, SPRING - TUBULAR, COILED, STANDARD DUTY, UNS N07718 |
| 226 | SAE AS4833-1995 | 1995-06-01(R 2010) | English | Aircraft New Tire Standard - Bias and Radial |
| 227 | SAE AS4983-1995 | 1995-06-01(R 2006) | English | Spring Pins, Tubular, Coiled Corrosion Resistant Nickel Base Alloy, Procurement Specification for - UNS N07718
DoD Adopted |
| 228 | SAE AS3577-1995 | 1995-06-01(R 2006) | English | Pin, Spring - Tubular, Coiled, Standard Duty, UNS N07718
DoD Adopted |
| 229 | SAE J1137-1995 | 1995-06-01(R 2002) | English | Hydraulic Valves for Motor Vehicle Brake Systems - Performance Requirements |
| 230 | SAE J1725-1995 | 1995-06-01(R 1999) | English | Structural Modification for Personally Licensed Vehicles to Meet the Transportation Needs of Persons with Disabilities |
| 231 | SAE J614-1995 | 1995-06-01 | English | Engine and Transmission Dipstick Marking
DoD Adopted |
| 232 | SAE J930-1995 | 1995-06-01 | English | (R) Storage Batteries for Off-Road Self-Propelled Work Machines, Standard |
| 233 | SAE J226-1995 | 1995-06-01 | English | (R) Engine Preheaters
ANSI Approved |
| 234 | SAE J2265-1995 | 1995-06-01 | English | Diesel Engines - Diesel Fuel - Performance Requirement and Test Method for Assessing Fuel Lubricity, Standard; |
| 235 | SAE AS4983-1995 | 1995-06-01 | English | Spring Pins, Tubular, Coiled Corrosion Resistant Nickel Base Alloy Procurement Specification For |
| 236 | SAE AS1198-1995 | 1995-06-01 | English | AEROSPACE WIRE AND CABLES METHODS OF TESTING |
| 237 | SAE ARP1877-1995 | 1995-06-01 | English | FABRICATION OF FORM - FIT POLYURETHANE FOAM HELMET |
| 238 | SAE AIR784C-1995 | 1995-06-01 | English | Interrelation of Engine Design and Burner Configuration with Selection and Performance of Electrical Ignition Systems for Gas Turbine Engines |
| 239 | SAE J383-1995 | 1995-06-01 | English | (R) Motor Vehicle Seat Belt Anchorages - Design Recommendations |
| 240 | SAE J335-1995 | 1995-06-01 | English | (R) Multiposition Small Engine Exhaust System Fire Ignition Suppression
DoD Adopted |
| 241 | SAE AS8032-1995 | 1995-06-01 | English | AIRCRAFT GENERAL PURPOSE ELECTRICAL WIRE, MINIMUM |
| 242 | SAE AMS1550B-1995 | 1995-06-01 | English | Cleaner, Water Base, Aircraft Interior Hard Surface Materials |
| 243 | SAE J141-1995 | 1995-06-01 | English | (R) Seat Belt Hardware Performance Requirements
ANSI Approved |
| 244 | SAE J1706-1995 | 1995-06-01 | English | (R) Production, Handling and Dispensing of SAE J1703 Motor Vehicle Brake Fluids, Recommended Practice |
| 245 | SAE J997-1995 | 1995-05-01(R 2013) | English | Spark Arrester Test Carbon |
| 246 | SAE ARP4961-1995 | 1995-05-01(R 2013) | English | Weights, Tube Fitting, Estimating, Weighing and Maintaining, Procedure for |
| 247 | SAE ARP4968-1995 | 1995-05-01(R 2013) | English | Installation Standard for Couplings |
| 248 | SAE AS3550-1995 | 1995-05-01(R 2012) | English | ASSEMBLY NUT, PLATE, REMOVABLE SELF-LOCKING NUT |
| 249 | SAE AIR1168/14-1995 | 1995-05-01(R 2011) | English | Spacecraft Life Support Systems |
| 250 | SAE AIR737E-1995 | 1995-05-01(R 2008) | English | (R) AEROSPACE HYDRAULIC AND PNEUMATIC SPECIFICATIONS, STANDARDS, RECOMMENDED PRACTICES, AND INFORMATION REPORTS |
| 251 | SAE AS4216-1995 | 1995-05-01(R 2007) | English | FITTING, BEAM SEAL, MALE BULKHEAD TUBE END, INTERNAL SWAGE, 4000 psi, HYDRAULIC |
| 252 | SAE AS4793-1995 | 1995-05-01(R 2007) | English | Fitting, Beam Seal, Male Tube End, Internal Swage, 4000 psi, Hydraulic |
| 253 | SAE AS103A-1995 | 1995-05-01(R 2007) | English | Fitting Assembly, Cross, Flareless and Short Flareless, Reducer, Retained Nut |
| 254 | SAE AS4842/1-1995 | 1995-05-01(R 2007) | English | Fittings, 37 Degrees Flared to Pipe Threaded, Fluid Connection
DoD Adopted |
| 255 | SAE AS4875/1-1995 | 1995-05-01(R 2007) | English | Fittings, Straight Thread Boss or Flanged to 37 Degree Flared, Fluid Connection
DoD Adopted |
| 256 | SAE AS4875/2-1995 | 1995-05-01(R 2007) | English | Fittings, Flanged to Beaded, Fluid Connection
DoD Adopted |
| 257 | SAE AS4843/2-1995 | 1995-05-01(R 2007) | English | Fittings, Beaded to Pipe Threaded, Fluid Connection
DoD Adopted |
| 258 | SAE AS4875-1995 | 1995-05-01(R 2007) | English | Fittings, Straight Threaded Boss or Flanged, Fluid Connection
DoD Adopted |
| 259 | SAE AS4843/1-1995 | 1995-05-01(R 2007) | English | Fittings, Beaded to 37 Degrees Flared, Fluid Connection
DoD Adopted |
| 260 | SAE AS4843-1995 | 1995-05-01(R 2007) | English | Fittings, Beaded, Fluid Connection
DoD Adopted |
| 261 | SAE AS4842/2-1995 | 1995-05-01(R 2007) | English | Fittings, Flareless to Pipe Threaded, Fluid Connection |
| 262 | SAE ARP4968-1995 | 1995-05-01(R 2007) | English | Installation Standard for Couplings |
| 263 | SAE ARP4961-1995 | 1995-05-01(R 2007) | English | Weights, Tube Fitting, Estimating, Weighing and Maintaining, Procedure for |
| 264 | SAE AS3548-1995 | 1995-05-01(R 2006) | English | Basket, Removable Self-Locking Nut, UNS S66286 - UNS S66286; FSC 5310
DoD Adopted |
| 265 | SAE AS3549-1995 | 1995-05-01(R 2006) | English | Sleeve, Removable Self-Locking Nut, UNS S30403 - UNS S30403; FSC 5310
DoD Adopted |
| 266 | SAE AS100003C-1995 | 1995-05-01(R 2006) | English | Gasket-Type XII, XIV-A, and XIV-B Engine Accessory Drive |
| 267 | SAE AS3550-1995 | 1995-05-01(R 2006) | English | Assembly Nut, Plate, Removable Self-Locking Nut
DoD Adopted |
| 268 | SAE AS100001C-1995 | 1995-05-01(R 2006) | English | Gasket-Type X or XV Engine Accessory Drive |
| 269 | SAE AS3547-1995 | 1995-05-01(R 2006) | English | Assembly Nut and Clip, Removable Self-Locking Nut, UNS S66286 - UNS S66286; FSC 5310
DoD Adopted |
| 270 | SAE AS100007C-1995 | 1995-05-01(R 2006) | English | Gasket - Type XIX Engine Accessory Drive |
| 271 | SAE AS100006C-1995 | 1995-05-01(R 2006) | English | Gasket - Type XVI Engine Accessory Drive |
| 272 | SAE AS100005C-1995 | 1995-05-01(R 2006) | English | Gasket - Type XIV-C Engine Accessory Drive |
| 273 | SAE AIR1168/14-1995 | 1995-05-01(R 2006) | English | Spacecraft Life Support Systems |
| 274 | SAE AS100002C-1995 | 1995-05-01(R 2006) | English | Gasket-Type XI Engine Accessory Drive |
| 275 | SAE AS100004C-1995 | 1995-05-01(R 2006) | English | Gasket - Type XIII Engine Accessory Drive |
| 276 | SAE AS4841-1995 | 1995-05-01(R 2005) | English | Fittings, 37 Degree Flared, Fluid Connection
DoD Adopted |
| 277 | SAE AS4842-1995 | 1995-05-01(R 2004) | English | Fittings and Bosses, Pipe Threaded, Fluid Connection
DoD Adopted |
| 278 | SAE AMS3023-1995 | 1995-05-01(R 2003) | English | Fluid, Reference for Testing Polyol Ester (and Diester) Resistant Material |
| 279 | SAE J997-1995 | 1995-05-01(R 2000) | English | Spark Arrester Test Carbon |
| 280 | SAE J2203-1995 | 1995-05-01(R 1999) | English | SAE 17.6 Cubic Inch Spark Plug Rating Engine |
| 281 | SAE J2093-1995 | 1995-05-01(R 1999) | English | Design Considerations for Wheelchair Lifts for Entry to or Exit from a Personally Licensed Vehicle
ANSI Approved |
| 282 | SAE J2092-1995 | 1995-05-01(R 1999) | English | Testing of Wheelchair Lifts for Entry to or Exit from a Personally Licensed Vehicle |
| 283 | SAE AIR4416-1995 | 1995-05-01 | English | Helicopter Turbine Engine Wash |
| 284 | SAE J1639-1995 | 1995-05-01 | English | (R) Classification System for Automotive Polyamide (PA) Plastics, Recommended Practice |
| 285 | SAE AIR4279-1995 | 1995-05-01 | English | Heat Up Time |
| 286 | SAE J530-1995 | 1995-05-01 | English | Automotive Pipe Fittings |
| 287 | SAE J531-1995 | 1995-05-01 | English | Automotive Pipe, Filler, and Drain Plugs
DoD Adopted |
| 288 | SAE J530-1995 | 1995-05-01 | English | Automotive Pipe Fittings
DoD Adopted |
| 289 | SAE AS4793-1995 | 1995-05-01 | English | Fitting, Beam Seal, Male Tube End, Internal Swage, 4000 psi, Hydraulic |
| 290 | SAE AIR4416-1995 | 1995-05-01 | English | Helicopter Turbine Engine Wash |
| 291 | SAE AMS3714D-1995 | 1995-04-01(R 2013) | English | Core, Overexpanded Honeycomb, Polyamide Paper Base, Phenolic Coated |
| 292 | SAE J1353-1995 | 1995-04-01(R 2007) | English | Nomenclature鈥擟lam Bunk Skidder |
| 293 | SAE AS4270-1995 | 1995-04-01(R 2005) | English | Validation Methods for Mil-Std-1760 Mission Stores |
| 294 | SAE AMS3136E-1995 | 1995-04-01(R 2005) | English | Coating Material, Phenolic Resin, PTFE Filled Pigmented, 150 掳C (302 掳F) Cure
DoD Adopted |
| 295 | SAE AS4764-1995 | 1995-04-01(R 2005) | English | Validation Methods for Mil-Std-1760 Aircraft Station Interfaces |
| 296 | SAE AMS3670/3B-1995 | 1995-04-01(R 2004) | English | Polyamide-Imide Bar, Rod, and Shapes 12% Graphite - 3% Polytetrafluoroethylene Filled |
| 297 | SAE AMS3670/1B-1995 | 1995-04-01(R 2004) | English | UNFILLED POLYAMIDE-IMIDE BAR, ROD, AND SHAPES |
| 298 | SAE AMS3670B-1995 | 1995-04-01(R 2003) | English | Polyamide-Imide Bar, Rod, and Shapes Molded or Extruded |
| 299 | SAE AMS3714D-1995 | 1995-04-01(R 2003) | English | Core, Overexpanded Honeycomb, Polyamide Paper Base, Phenolic Coated |
| 300 | SAE AMS3359B-1995 | 1995-04-01(R 2001) | English | Silicone Potting Compound, Elastomeric Two-Part, General Purpose 200 to 400 Poises (20 to 40 Pa-s) Viscosity |
| 301 | SAE AMS3358B-1995 | 1995-04-01(R 2001) | English | Silicone Potting Compound, Elastomeric Two-Part, General Purpose 80 to 180 Poise (8 to 18 Pa-s) Viscosity |
| 302 | SAE AMS3670/4C-1995 | 1995-04-01(R 2000) | English | Polyamide-Imide Bar, Rod, and Shapes 30% Glass Fiber |
| 303 | SAE AMS3670/5C-1995 | 1995-04-01(R 2000) | English | Polyamide-Imide Bar, Rod, and Shapes 30% Carbon Fiber |
| 304 | SAE AS4764-1995 | 1995-04-01 | English | Validation Methods for MIL-STD-1760 Aircraft Station Interfaces |
| 305 | SAE AS4270-1995 | 1995-04-01 | English | Validation Methods for MIL-STD-1760 Mission Stores |
| 306 | SAE J1553-1995 | 1995-04-01 | English | (R) Cross Peel Test for Automotive-Type Adhesives for Fiber- Reinforced Plastic (FRP) Bonding, Recommended Practice |
| 307 | SAE AMS4615F-1995 | 1995-04-01 | English | SILICON BRONZE RODS AND BARS, 95.5Cu-3.2Si, HARD TEMPER |
| 308 | SAE J2264-1995 | 1995-04-01 | English | Chassis Dynamometer Simulation of Road Load Using Coastdown Techniques, Recommended Practice |
| 309 | SAE ARP1987/2-1995 | 1995-03-01(R 2013) | English | Titles, Hose and Hose Assembly, SAE G-3D Subcommittee, Selection of |
| 310 | SAE AIR4906-1995 | 1995-03-01(R 2013) | English | Droplet Sizing Instrumentation Used in Icing Facilities |
| 311 | SAE AS95-1995 | 1995-03-01(R 2013) | English | FITTING ASSEMBLY, CROSS, REDUCER AND NONREDUCER, INTERNAL FLARE ON ONE END, TO FLARED TUBE |
| 312 | SAE AIR4894-1995 | 1995-03-01(R 2012) | English | Landing Gear Stability |
| 313 | SAE AMS2632A-1995 | 1995-03-01(R 2008) | English | Inspection, Ultrasonic, of Thin Materials 0.50 Inch (12.7 mm) and Under in Cross-Sectional Thickness |
| 314 | SAE MA2024-1995 | 1995-03-01(R 2007) | English | Flange Profiles, V-Coupling, Design Standard, Metric |
| 315 | SAE AS95-1995 | 1995-03-01(R 2007) | English | Fitting Assembly, Cross, Reducer and Nonreducer, Internal Flare on One End, to Flared Tube |
| 316 | SAE ARP4927-1995 | 1995-03-01(R 2007) | English | Integration Procedures for the Introduction of New Systems to the Cockpit |
| 317 | SAE AIR4906-1995 | 1995-03-01(R 2007) | English | Droplet Sizing Instrumentation Used in Icing Facilities |
| 318 | SAE ARP1987/2-1995 | 1995-03-01(R 2007) | English | Titles, Hose and Hose Assembly, SAE G-3D Subcommittee, Selection of |
| 319 | SAE AIR4894-1995 | 1995-03-01(R 2006) | English | Landing Gear Stability |
| 320 | SAE AMS1453-1995 | 1995-03-01(R 2004) | English | Disinfectant Cleaner for Aircraft Interior General Purpose Liquid
DoD Adopted |
| 321 | SAE CRP-009-1995 | 1995-03-01 | English | Heavy Truck Crashworthiness - Phase I - To Purchase: Contact IHS at 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 322 | SAE MA2024-1995 | 1995-03-01 | English | FLANGE PROFILES, V-COUPLING, DESIGN STANDARD, METRIC |
| 323 | SAE J385-1995 | 1995-03-01 | English | Motor Vehicle Seat Belt Anchorages - Performance Requirements |
| 324 | SAE AIR4894-1995 | 1995-03-01 | English | Landing Gear Stability |
| 325 | SAE AMS4053B-1995 | 1995-03-01 | English | ALUMINUM ALLOY PLATE 1.0MG-0.60SI-0.28CU-0.25CR (6061-T651) |
| 326 | SAE AMS3574A-1995 | 1995-03-01 | English | POLYURETHANE, FOAM-IN-PLACE, RIGID CLOSED CELL, FOR HELMET LINERS |
| 327 | SAE AS8027-1995 | 1995-02-01(R 2018) | English | Crew Member Oxygen Regulators, Demand |
| 328 | SAE AMS3692C-1995 | 1995-02-01(R 2014) | English | Adhesive Compound, Epoxy Resing High Temperature Application |
| 329 | SAE AS8027-1995 | 1995-02-01(R 2013) | English | Crew Member Oxygen Regulators, Demand |
| 330 | SAE J1102-1995 | 1995-02-01(R 2013) | English | Mechanical and Material Requirements for Wheel Bolts |
| 331 | SAE ARP813B-1995 | 1995-02-01(R 2010) | English | Maintainability Recommendations for Aircraft Wheel and Brake Design |
| 332 | SAE AS8027-1995 | 1995-02-01(R 2008) | English | Crew Member Oxygen Regulators, Demand |
| 333 | SAE AMS3692C-1995 | 1995-02-01(R 2005) | English | Adhesive Compound, Epoxy Resin High Temperature Application |
| 334 | SAE J115-1995 | 1995-02-01(R 2003) | English | Safety Signs |
| 335 | SAE AIR4289-1995 | 1995-02-01(R 2001) | English | Handbook For The SAE AS4075 High Speed Ring Bus Standard |
| 336 | SAE AMS3361B-1995 | 1995-02-01(R 2001) | English | Silicone Potting Compound, Elastomeric Two-Part, General Purpose 150 to 400 Poise (15 to 40 Pa-s) Viscosity |
| 337 | SAE J2132-1995 | 1995-02-01(R 1999) | English | Manual Transmissions and Transaxle High-Speed Lubrication, Unbalance, and Seizure Evaluation |
| 338 | SAE AMS2645K-1995 | 1995-02-01 | English | Fluorescent Penetrant Inspection, by the Latest Issue of ASTM E 1417 |
| 339 | SAE J1102-1995 | 1995-02-01 | English | (R) Mechanical and Material Requirements for Wheel Bolts, Standard |
| 340 | SAE AMS3326D-1995 | 1995-02-01 | English | Fluorosilicone Rubber Fuel and Oil Resistant 50 - 65 |
| 341 | SAE R-144-1995 | 1995-02-01 | English | The Birth of Chrysler Corporation and Its Engineering Legacy - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 342 | SAE R-152-1995 | 1995-02-01 | English | A Glossary of Corrosion-Related Terms Used in Science and Industry - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 343 | SAE AMS7706B-1995 | 1995-02-01 | English | IRON BAR, SHEET, STRIP, AND PLATE, COMMERCIALLY PURE - HOT ROLLED, ANNEALED |
| 344 | SAE AMS6530J-1995 | 1995-02-01 | English | STEEL TUBING, SEAMLESS, 0.50NI - 0.55CR - 0.20MO (0.28 - 0.33C) |
| 345 | SAE J1767-1995 | 1995-01-01(R 2014) | English | Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials, Recommended Practice |
| 346 | SAE J485-1995 | 1995-01-01(R 2013) | English | Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins |
| 347 | SAE J1454-1995 | 1995-01-01(R 2012) | English | Dynamic Durability Testing of Seat Cushions for Off-Road Work Machines |
| 348 | SAE AMS1775B-1995 | 1995-01-01(R 2008) | English | Fabric, Nylon Upholstery Fire Retardant |
| 349 | SAE MA2274-1995 | 1995-01-01(R 2007) | English | FITTING END, BEAM SEAL, BULKHEAD, EXTERNAL THREAD, DESIGN STANDARD, METRIC |
| 350 | SAE MA2276-1995 | 1995-01-01(R 2007) | English | Nut, Beam Seal, Slip-On Metric |
| 351 | SAE MA2271-1995 | 1995-01-01(R 2007) | English | FITTING END, BEAM SEAL, SLIP-ON NUT, DESIGN STANDARD, METRIC |
| 352 | SAE MA2273-1995 | 1995-01-01(R 2007) | English | FITTING END, BEAM SEAL, EXTERNAL THREAD, DESIGN STANDARD, METRIC |
| 353 | SAE AS5018-1995 | 1995-01-01(R 2007) | English | Washer, Flat, Beam Seal Fitting |
| 354 | SAE AMS5341C-1995 | 1995-01-01(R 2006) | English | Steel Castings, Investment, Corrosion Resistant 19.5Cr - 10.5Ni - 0.25S (Type 303) Solution Heat Treated - UNS J92711 |
| 355 | SAE J1454-1995 | 1995-01-01(R 2006) | English | Dynamic Durability Testing of Seat Cushions for Off-Road Work Machines |
| 356 | SAE AMS5365D-1995 | 1995-01-01(R 2006) | English | Steel Castings, Sand, Corrosion and Heat Resistant 24.5Cr - 20.5Ni Solution Heat Treated - UNS S92411
DoD Adopted |
| 357 | SAE AMS5395C-1995 | 1995-01-01(R 2006) | English | Alloy Iron Castings, Ductile, Sand, Corrosion Resistant 22Ni (2.5 - 3.0C) as Cast - UNS F43030
DoD Adopted |
| 358 | SAE AS4492-1995 | 1995-01-01(R 2004) | English | Survivor Locator Lights |
| 359 | SAE J485-1995 | 1995-01-01(R 1998) | English | Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins
ANSI Approved |
| 360 | SAE MA2273-1995 | 1995-01-01 | English | FITTING END, BEAM SEAL, EXTERNAL THREAD, DESIGN STANDARD, METRIC |
| 361 | SAE AMS2268B-1995 | 1995-01-01 | English | Chemical Check Analysis Limits Cast Nickel and Nickel Alloys |
| 362 | SAE J2253-1995 | 1995-01-01 | English | Test Procedures for Automotive Structural Composite Materials, Standard |
| 363 | SAE MA2276-1995 | 1995-01-01 | English | Nut, Beam Seal, Slip-On Metric |
| 364 | SAE MA2274-1995 | 1995-01-01 | English | FITTING END, BEAM SEAL, BULKHEAD, EXTERNAL THREAD, DESIGN STANDARD, METRIC |
| 365 | SAE MA2271-1995 | 1995-01-01 | English | FITTING END, BEAM SEAL, SLIP-ON NUT, DESIGN STANDARD, METRIC |
| 366 | SAE J412-1995 | 1995-01-01 | English | General Characteristics and Heat Treatments of Steels |
| 367 | SAE AMS1525D-1995 | 1995-01-01 | English | CLEANER FOR AIRCRAFT EXTERIOR METALLIC SURFACES WIPE SOLVENT, COLD OPERATIONS |
| 368 | SAE J223-1995 | 1995-01-01 | English | Symbols and Color Codes for Maintenance Instructions, Container and Filler Identification |
| 369 | SAE J1712-1995 | 1995-01-01 | English | Reporting on Emission Testing for In-Use Light -Duty Trucks and Passenger Vehicles, Recommended Practice |
| 370 | SAE J140-1995 | 1995-01-01 | English | (R) Seat Belt Hardware Test Procedures |
| 371 | SAE J2254-1995 | 1995-01-01 | English | Fluid Power Piping Cleaning Process, Information Report |
| 372 | SAE J1604-1995 | 1995-01-01 | English | (R) Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders Standard |
| 373 | SAE J2017-1995 | 1995-01-01 | English | Guidelines for the Development of Performance-Based Technician Training Programs |
| 374 | SAE J1755-1995 | 1995-01-01 | English | Guidelines for Usage of Stainless Steel and Bimetal for Exterior Automotive Bright Trim, Recommended Practice |
| 375 | SAE AS4075/1-1995 | 1995-01-01 | English | Optical Implementation Relating to the High Speed Ring Bus (HSRB)
ANSI Approved |
| 376 | SAE J1767-1995 | 1995-01-01 | English | Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials, Recommended Practice |
| 377 | SAE AS7106/5-1995 | 1995-01-01 | English | National Aerospace and Defense Contractors Accreditation Program Self-Release Agreements - Requirements |
| 378 | SAE AS7106/2A-1995 | 1995-01-01 | English | National Aerospace and Defense Contractors Accreditation Program Requirements for Corrective Action and Disposition System for Nonconforming Material |
| 379 | SAE ARP670B-1995 | 1995-01-01 | English | Terminals, Aircraft Ignition |
| 380 | SAE HS-215-1995 | 1995-01-01 | English | SAE Motor Vehicle Safety and Environmental Terminology |
| 381 | SAE AS7106/3-1995 | 1995-01-01 | English | National Aerospace and Defense Contractors Accreditation Program Quality Assurance Program Requirements - Procurement |
| 382 | SAE AS7106/1-1995 | 1995-01-01 | English | National Aerospace and Defense Contractors Accreditation Program Requirements for the Control of Deliverable Production Software |
| 383 | SAE ARP492C-1994 | 1994-12-01(R 2014) | English | Aircraft Engine Fuel Pump Cavitation Endurance Test(DoD Adopted) |
| 384 | SAE AIR974B-1994 | 1994-12-01(R 2008)(S 2013) | English | Long-Term Storage of Missile Hydraulic Systems |
| 385 | SAE AIR974A-1994 | 1994-12-01(R 2008) | English | Long-Term Storage of Missile Hydraulic Systems |
| 386 | SAE AS4694A-1994 | 1994-12-01(R 2007) | English | Fitting Assembly, Cap, Hollow End, Acorn, Short Flareless |
| 387 | SAE ARP492C-1994 | 1994-12-01(R 2007) | English | Aircraft Engine Fuel Pump Cavitation Endurance Test
DoD Adopted |
| 388 | SAE AIR746B-1994 | 1994-12-01(R 2006) | English | Environmental Control for Civil Supersonic Transport |
| 389 | SAE AS567J-1994 | 1994-12-01(R 2006) | English | Safety Cable, Safety Wire, Key Washers, and Cotter Pins for Propulsion Systems, General Practices for Use of |
| 390 | SAE AS4702A-1994 | 1994-12-01(R 2004) | English | Nut, Retained, Short Flareless
DoD Adopted |
| 391 | SAE AS4685A-1994 | 1994-12-01(R 2004) | English | Fitting, Elbow, 90 Degrees, Reducer, Flareless and Short Flareless |
| 392 | SAE AS4688A-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Reducer, Flareless and Short Flareless |
| 393 | SAE AS4681A-1994 | 1994-12-01(R 2004) | English | Fitting, Union, Reducer/Expander Bulkhead, Flareless and Short Flareless |
| 394 | SAE AS100A-1994 | 1994-12-01(R 2004) | English | FITTING, CROSS, SHORT FLARELESS |
| 395 | SAE AS102A-1994 | 1994-12-01(R 2004) | English | FITTING, CROSS, REDUCER, FLARELESS AND SHORT FLARELESS |
| 396 | SAE AS4680A-1994 | 1994-12-01(R 2004) | English | Fitting, Union, Reducer, Short Flareless and Flareless to Boss |
| 397 | SAE AS4682A-1994 | 1994-12-01(R 2004) | English | Fitting, Elbow, 45 Degrees, Reducer, Flareless and Short Flareless |
| 398 | SAE AS4677A-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Bulkhead on Run, Boss on Side, Short Flareless |
| 399 | SAE AS4665A-1994 | 1994-12-01(R 2004) | English | Fitting, Adapter, Union and Reducer, Short Flareless to Boss |
| 400 | SAE AS4676A-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Bulkhead and Boss on Run, Short Flareless |
| 401 | SAE AS4660A-1994 | 1994-12-01(R 2004) | English | Nut, Short Flareless |
| 402 | SAE AS4661A-1994 | 1994-12-01(R 2004) | English | Fitting Assembly, Cap, Short Flareless |
| 403 | SAE AS4662A-1994 | 1994-12-01(R 2004) | English | Fitting, Plug, Short Flareless |
| 404 | SAE AS4673A-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Bulkhead on Side, Short Flareless |
| 405 | SAE AS4672B-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Bulkhead on Run, Short Flareless |
| 406 | SAE AS4671A-1994 | 1994-12-01(R 2004) | English | Fitting, Tee, Short Flareless |
| 407 | SAE AS4663A-1994 | 1994-12-01(R 2004) | English | Fitting, Union, Short Flareless |
| 408 | SAE AS4669A-1994 | 1994-12-01(R 2004) | English | Fitting, Elbow, 90 Degrees, Bulkhead, Short Flareless |
| 409 | SAE AS4668A-1994 | 1994-12-01(R 2004) | English | Fitting, Elbow, 90 Degrees, Short Flareless |
| 410 | SAE AS4666A-1994 | 1994-12-01(R 2004) | English | Fitting, Elbow, 45 Degrees, Bulkhead, Short Flareless |
| 411 | SAE AS4664A-1994 | 1994-12-01(R 2004) | English | Fitting, Union, Bulkhead, Short Flareless |
| 412 | SAE R-143-1994 | 1994-12-01 | English | ALTERNATIVE FUELS: Emissions, Economics, and Performance - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 413 | SAE J1567-1994 | 1994-12-01 | English | COLLISION DETECTION SERIAL DATA COMMUNICATIONS MUL |
| 414 | SAE J1178/ ISO 11169-1994 | 1994-12-01 | English | (R) Machinery for Forestry - Wheeled Special Machines - Vocabulary, Performance Test Methods, and Criteria for Brake Systems, Standard - WITHDRAWN - NO LONGER AVAILABLE |
| 415 | SAE J421-1994 | 1994-12-01 | English | CLEANLINESS RATING OF STEELS BY THE MAGNETIC PARTICLE METHOD |
| 416 | SAE ARP492C-1994 | 1994-12-01 | English | Aircraft Engine Fuel Pump Cavitation Endurance Test |
| 417 | SAE J2068-1994 | 1994-12-01 | English | Combination Turn Signal Hazard Warning Signal Flashers, Recommended Practice |
| 418 | SAE AS4702A-1994 | 1994-12-01 | English | Nut, Retained, Short Flareless |
| 419 | SAE MA4811-1994 | 1994-11-01(R 2012) | English | Insert - Thin Wall, Self-Locking, Metric Short and Long Length Installation and Removal Of |
| 420 | SAE MA4812-1994 | 1994-11-01(R 2012) | English | INSERT - THIN WALL, METRIC SHORT AND LONG HOLE PREPARATION FOR |
| 421 | SAE AS3542-1994 | 1994-11-01(R 2012) | English | COVER - TYPE XVI, XVII-C, D, E, AND F ENGINE ACCESSORY DRIVE |
| 422 | SAE AS3551-1994 | 1994-11-01(R 2012) | English | PACKING, PREFORMED – O-RING SEAL AMS7272 |
| 423 | SAE AMS5389C-1994 | 1994-11-01(R 2007) | English | Alloy Castings, Sand, Corrosion and Heat Resistant 55Ni - 16.5Cr - 17Mo - 4.5W - 5.8Fe - 0.40V Solution Heat Treated - UNS N10002 |
| 424 | SAE AMS5361E-1994 | 1994-11-01(R 2007) | English | Steel Castings, Sand and Centrifugal, Corrosion and Heat Resistant 18.5Cr - 13.5Ni - 2.1Mo Solution Heat Treated - UNS J93072 |
| 425 | SAE AS3225B-1994 | 1994-11-01(R 2006) | English | Cover - Engine Accessory Drive, Round, 10.000 Bolt Circle, AMS 4490 |
| 426 | SAE AS3221A-1994 | 1994-11-01(R 2006) | English | Cover - Engine Accessory Drive, Square, 2.653 Bolt Circle, AMS 4490 |
| 427 | SAE MA3520-1994 | 1994-11-01(R 2006) | English | Insert - Thin Wall, Short Self-Locking, 550 Degrees C, Silver Plated UNS N07718, MJ Thread, Metric - UNS N07718 |
| 428 | SAE MA3521-1994 | 1994-11-01(R 2006) | English | Insert - Thin Wall, Long Self-Locking, 550 Degrees C, Silver Plated UNS N07718, MJ Thread, Metric - UNS N07718 |
| 429 | SAE AS3224A-1994 | 1994-11-01(R 2006) | English | Cover - Engine Accessory Drive, Round, 8.000 Bolt Circle, AMS 4490 |
| 430 | SAE AS3222B-1994 | 1994-11-01(R 2006) | English | Cover - Engine Accessory Drive, Square, 5.000 Bolt Circle, AMS 4490 |
| 431 | SAE AS3223A-1994 | 1994-11-01(R 2006) | English | Cover - Engine Accessory Drive, Round, 5.000 Bolt Circle, AMS 4490 |
| 432 | SAE AS3551-1994 | 1994-11-01(R 2006) | English | Packing, Preformed - O-Ring Seal AMS 7272
DoD Adopted |
| 433 | SAE AS3542-1994 | 1994-11-01(R 2006) | English | Cover - Type XVI, XVII-C, D, E, and F Engine Accessory Drive |
| 434 | SAE MA4812-1994 | 1994-11-01(R 2006) | English | Insert - Thin Wall, Metric Short and Long Hole Preparation for |
| 435 | SAE MA4811-1994 | 1994-11-01(R 2006) | English | Insert - Thin Wall, Self-Locking, Metric Short and Long Length Installation and Removal of |
| 436 | SAE AS3224B-1994 | 1994-11-01(R 2006) | English | COVER - ENGINE ACCESSORY DRIVE, ROUND, 8.000 BOLT CIRCLE, AMS4490 (UNS M11910) - UNS M11910 |
| 437 | SAE AMS3894/17A-1994 | 1994-11-01(R 2005) | English | Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 200 (1379) Tensile, 18.0 (124) Modulus, 120 (248) |
| 438 | SAE AS3483A-1994 | 1994-11-01(R 2001) | English | (R) Nut, Self Locking, Hexagon, Regular Height, UNS S66286, Class: 125 ksi/800 Degrees F - UNS S66286
DoD Adopted |
| 439 | SAE AMS5310G-1994 | 1994-11-01(R 2000) | English | Iron Castings, Pearlitic Malleable |
| 440 | SAE J1819-1994 | 1994-11-01(R 1999) | English | Securing Child Restraint Systems in Motor Vehicles |
| 441 | SAE J2043-1994 | 1994-11-01 | English | Nonmetallic Fuel System Tubing, Standard |
| 442 | SAE J1819-1994 | 1994-11-01 | English | Securing Child Restraint Systems in Motor Vehicles |
| 443 | SAE AMS5358C-1994 | 1994-11-01 | English | Steel Castings, Investment, Corrosion Resistant 18Cr - 9Ni Solution Heat Treated - UNS J92602; Reaffirmed Noncurrent September 2007 |
| 444 | SAE AMS6321E-1994 | 1994-11-01 | English | STEEL BARS, FORGINGS, AND TUBING, 0.42CR - 0.30NI - 0.12MO - 0.003B (0.38 - 0.43C) (81B40) |
| 445 | SAE AMS3907A-1994 | 1994-10-01(R 2014) | English | (R) Cloth, Aramid Basket and Plain Weave |
| 446 | SAE ARP1926-1994 | 1994-10-01(R 2014) | English | Cure Monitor, Electrical Methods |
| 447 | SAE J1366-1994 | 1994-10-01(R 2007) | English | Rating Lift Cranes Operating on Platforms in the Ocean Environment |
| 448 | SAE AS1477B-1994 | 1994-10-01(R 2007) | English | Hose Assembly, Flexible, Low Pressure, Flareless, Potable Water, 45 Degrees to 45 Degrees |
| 449 | SAE AS1475B-1994 | 1994-10-01(R 2007) | English | Hose Assembly, Flexible, Low Pressure, Flareless, Potable Water, Straight to 90 Degrees |
| 450 | SAE AS1474B-1994 | 1994-10-01(R 2007) | English | Hose Assembly, Flexible, Low Pressure, Flareless, Potable Water, Straight to 45 Degrees |
| 451 | SAE AS1473B-1994 | 1994-10-01(R 2007) | English | Hose Assembly, Flexible, Low Pressure, Flareless, Potable Water, Straight to Straight |
| 452 | SAE AMS3907A-1994 | 1994-10-01(R 2005) | English | (R) Cloth, Aramid Basket and Plain Weave |
| 453 | SAE AMS7260E-1994 | 1994-10-01(R 2001) | English | Rings, Butadiene-Acrylonitrile (NBR) Rubber, Molded Fuel and Low Temperature Resistant 70 - 80
DoD Adopted |
| 454 | SAE AMS7268C-1994 | 1994-10-01(R 2001) | English | Rings, Sealing, Silicone Rubber Low Compression Set, Non-Oil Resistant 65 - 75
DoD Adopted |
| 455 | SAE ARP4806-1994 | 1994-10-01 | English | Aerospace - Deicing/Anti-Icing Self-Propelled Vehicle Functional Requirements |
| 456 | SAE AMS1800B-1994 | 1994-10-01 | English | Foam, Fire Extinguishing Liquid Protein and Fluoroprotein |
| 457 | SAE ARP1926-1994 | 1994-10-01 | English | Cure Monitor, Electrical Methods |
| 458 | SAE ARP755B-1994 | 1994-10-01 | English | Aircraft Propulsion System Performance Station Designation and Nomenclature
DoD Adopted | ANSI Approved |
| 459 | SAE AMS7260E-1994 | 1994-10-01 | English | Rings, Butadiene-Acrylonitrile (NBR) Rubber, Molded Fuel and Low Temperature Resistant 70 - 80 |
| 460 | SAE J1366-1994 | 1994-10-01 | English | Rating Lift Cranes Operating on Platforms in the Ocean Environment |
| 461 | SAE J940-1994 | 1994-10-01 | English | Glossary of Carbon Steel Sheet and Strip Terms, Information Report |
| 462 | SAE AMS3792B-1994 | 1994-10-01 | English | (R) Tape, Low Modulus Aramid 300 (1334), 1000 (4448) and 8000 (13,345) Breaking Strength
DoD Adopted |
| 463 | SAE AMS7260E-1994 | 1994-10-01 | English | Rings, Butadiene-Acrylonitrile (NBR) Rubber, Molded Fuel and Low Temperature Resistant 70 - 80 |
| 464 | SAE J2219-1994 | 1994-10-01 | English | (R) Mobile Air Conditioning Industry Criteria and Guidelines, Information Report |
| 465 | SAE ARP4028-1994 | 1994-09-01(R 2014) | English | Aircraft/Engine Fuel Pump Two Phase (Slugging Flow) Inlet Performance Test and Evaluation |
| 466 | SAE ARP1987/1-1994 | 1994-09-01(R 2013) | English | Titles, SAE G-3B Subcommittee Documents, Selection Of |
| 467 | SAE ARP4904-1994 | 1994-09-01(R 2008) | English | Capability Guidelines for Computer Controlled Test Equipment for Hydraulic Components |
| 468 | SAE ARP4028-1994 | 1994-09-01(R 2007) | English | Aircraft/Engine Fuel Pump Two Phase (Slugging Flow) Inlet Performance Test and Evaluation |
| 469 | SAE ARP1987/1-1994 | 1994-09-01(R 2007) | English | Titles, SAE G-3B Subcommittee Documents, Selection Of |
| 470 | SAE AIR4002-1994 | 1994-09-01(R 2004) | English | 8000 psi Hydraulic Systems: Experience and Test Results |
| 471 | SAE AMS3336D-1994 | 1994-09-01(R 2001) | English | Silicone (PVMQ) Rubber Extreme-Low-Temperature Resistant 55 - 65
DoD Adopted |
| 472 | SAE AMS3644/2C-1994 | 1994-09-01 | English | PLASTIC ROD AND BAR, POLYIMIDE GRAPHITE / PTFE FILLED, MOLDED 15/10 |
| 473 | SAE AMS3808A-1994 | 1994-09-01 | English | Tape, Adhesive, Pressure- Sensitive Masking
DoD Adopted |
| 474 | SAE AMS3053-1994 | 1994-09-01 | English | Grease, Water Resistant Polyalphaolefin Base |
| 475 | SAE MAM2203B-1994 | 1994-09-01 | English | TOLERANCES, METRIC Aluminum Alloy Drawn Tubing |
| 476 | SAE AMS3644/1C-1994 | 1994-09-01 | English | PLASTIC ROD AND BAR, POLYIMIDE UNFILLED, MOLDED |
| 477 | SAE MAM3053-1994 | 1994-09-01 | English | Grease, Water Resistant Polyalphaolefin Base |
| 478 | SAE AMS2203K-1994 | 1994-09-01 | English | TOLERANCES |
| 479 | SAE ARP4028-1994 | 1994-09-01 | English | Aircraft/Engine Fuel Pump Two Phase (Slugging Flow) Inlet Performance Test and Evaluation |
| 480 | SAE J1054-1994 | 1994-09-01 | English | Warning Lamp Alternating Flashers, Recommended Practice |
| 481 | SAE AIR4918-1994 | 1994-08-01(R 2013) | English | Industry Practices and Guidelines for the Selection of Coiled Tubes, Flexible Hoses, Swivels, and Extension Fittings for Aircraft Fluid Systems |
| 482 | SAE J1301-1994 | 1994-08-01(R 2009) | English | Truck Deformation Classification |
| 483 | SAE J1621-1994 | 1994-08-01(R 2005) | English | Engine Retarder Dynamometer Test and Capability Rating Procedure |
| 484 | SAE AIR4918-1994 | 1994-08-01(R 2004) | English | Industry Practices and Guidelines for the Selection of Coiled Tubes, Flexible Hoses, Swivels, and Extension Fittings for Aircraft Fluid Systems |
| 485 | SAE AMS3193C-1994 | 1994-08-01(R 2001) | English | Silicone Rubber Sponge Closed Cell, Medium, Extreme Low Temperature
DoD Adopted |
| 486 | SAE AMS3194C-1994 | 1994-08-01(R 2001) | English | Silicone Rubber Sponge Closed Cell, Firm, Extreme Low Temperature
DoD Adopted |
| 487 | SAE J1618-1994 | 1994-08-01(R 2000) | English | Continuously Variable Transmission Test Code for Passenger Cars |
| 488 | SAE R-140-1994 | 1994-08-01 | English | BY THE NUMBERS Principles of Automotive Parts Management - To Purchase Call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide |
| 489 | SAE AMS4906A-1994 | 1994-08-01 | English | TITANIUM ALLOY SHEET & STRIP 6A1-4V CONT. ROLLED |
| 490 | SAE J1988-1994 | 1994-08-01 | English | Residual Aligning Moment Test, Recommended Practice |
| 491 | SAE AMS3728A-1994 | 1994-07-01(R 2014) | English | Epoxy Cresol Novolac Resin Low Molecular Weight |
| 492 | SAE ARP4050-1994 | 1994-07-01(R 2011) | English | BALANCING MACHINES - DESCRIPTION AND EVALUATION VERTICAL, TWO-PLANE, HARD-BEARING TYPE FOR GAS TURBINE ROTORS
ANSI Approved |
| 493 | SAE ARP4249-1994 | 1994-07-01(R 2006) | English | Bearing Corrosion Test Method |
| 494 | SAE MA3446A-1994 | 1994-07-01(R 2006) | English | BOLT, MACHINE - TEE HEAD, CHAMFERED CLASSIFICATION: 1210 MPA/730 掳C CLOSE TOL SHANK, UNS N07001, METRIC
DoD Adopted |
| 495 | SAE AS4897-1994 | 1994-07-01(R 2004) | English | Hose Assembly, Polytetrafluoroethylene (PTFE), Low Pressure, 450 Degrees F and Fireproof, Procurement Specification for |
| 496 | SAE AS4383A-1994 | 1994-07-01(R 2004) | English | Fitting Assembly, Reducer Ring Locked Port Connection to Beam Seal 5000 psi /8/ |
| 497 | SAE MAP1201-1994 | 1994-07-01(R 2004) | English | Tolerances, Hexagon Bar, Machined Flat and Forged Wrenching Flat Sizes for Fluid Fittings, Metric |
| 498 | SAE MA2119A-1994 | 1994-07-01(R 2004) | English | Fitting Assembly, Reducer Ring Locked Port Connection to Beam Seal 28 000 kPa, Metric |
| 499 | SAE AS4200A-1994 | 1994-07-01(R 2004) | English | Fitting Assembly, Adapter Ring Locked Port Connection to Beam Seal 8000 psi |
| 500 | SAE MA3446A-1994 | 1994-07-01 | English | BOLT, MACHINE - TEE HEAD, CHAMFERED CLASSIFICATION: 1210 MPA/730 °C CLOSE TOL SHANK, UNS N07001, METRIC |
|